Ok another Sub

To many ads? Support ODJT and see no ads!
sure whats the problem besides blown subs?
 
Cam,

If you are blowing this many subs you are trying to get more out of them than they are capable of.

Or you need to have your hearing checked because there is a problem some where.

Please tell us your gain chain, your EQ settings, processor settings etc..

Can't you hear the sub distorting or the voice coil bottoming out beofre it goes?

Is it ripping the paper cone or just frying the voice coils?
 
I actually did have my hearing checked it is fine and it is above average in frequecy reconition.

Signal Chain

Mixer xlr to crossover
Crossover High to Amp for main speakers
Crossover low to Mackie Input

Crossover settings

All Levels at 0 or even

Crossover frequency 80hz

Level on Mackie at 10 o'clock.


I never hear any distortion it just goes from working to not working. The voil coil frys and the main power fuse on the amplifer power supply blows. I have tested the speaker each time and it has no response. If I relapce the fuse there is no problem with the amplifer itself.

The last two times it has blown There has been no clipping on my main amplifer. There is not a clip light on the mackie so it hard to know if it is clipping but I assume that it is not. I have never had the limiter come on.
 
Cam,

What happens when you turn the gain on the sub all the way up?
 
Cam,

What happens when you turn the gain on the sub all the way up?


It would blow up in a few seconds, it is more amplification than the speaker can handle. I have never in the 3 years of owning the speakers been able to turn them more than 1/2 way up.

I tried contacting Mackie directly today. They could not help me.
 
Why are you using a crossover? The Mackie subs have one built in. You go from mixer into subs into tops. Have you tried this?

Maybe something in the chain is sending too hot a feed or maybe spikes. Start basic and then add the other stuff in.
 
I just downloaded the manual.

On the back there appears to be 2 XLR & 2 1/4" main outs right next to each other.

Maybe try running the XLR outs to your crossover then your mains amp. Then run the 1/4" outs direct to your sub (It will require a 1/4" to XLR adaptor).

I run out of my Mackie in a similar fashion and it works great.
 
We have only had a problem with 1 of the 6 mackie subs we have here at the office, and the only issue was blow fuse, due to a bad wall socket at a facility.

Do you have a power socket tester and a volt meter? I ALWAYS test voltage and proper plug wiring before giving it the juice.
 
We have only had a problem with 1 of the 6 mackie subs we have here at the office, and the only issue was blow fuse, due to a bad wall socket at a facility.

Do you have a power socket tester and a volt meter? I ALWAYS test voltage and proper plug wiring before giving it the juice.

I believe yours are the older versions (not made in China), aren't they?
 
You should see how things are in Mexico ;) . Fortunately the wiring in my house was done properly and I have enough juice available to run my toys. Cam, I would try what Jay mentioned and see if it works.

I would also follow Travis' suggestion checking the voltage and polarity of the outlets. I don't remember on which board I read this but I think it was Mike Pyle (I'm really not sure) suggested carrying a small extension cord with the wiring inverted. In case the power outlet was reversed the short chord would take care of this problem.
 
I would also follow Travis' suggestion checking the voltage and polarity of the outlets. I don't remember on which board I read this but I think it was Mike Pyle (I'm really not sure) suggested carrying a small extension cord with the wiring inverted. In case the power outlet was reversed the short chord would take care of this problem.

Not me.
 
Sorry Mike,
I can't remember which board and who the author was.