Line noise? ground problem? help! can't figure it out

To many ads? Support ODJT and see no ads!

T-Bone

New DJ
Dec 10, 2006
134
0
35
Princeton, NJ
t-bonedj.com
Running 2 Mackie SRM-450s. I usually get a slight hiss thats only barely audible in a silent room when turned up to 1/4 power. This happens even when not connected to anything on both mackies. But it doesn't bother me. Tonight however it seemed much louder. I figured it was unclean power or a ground problem but I couldn't seem to fix it. During one of the speachess the room went dead silent and to me it sounded like an air conditioner running in the backround. I've had this happen once before it wasn;t a big deal since it always becomes inaudib;le when i ply music but anytmime theres dead air or a speach etc it happens. Now it could just be the venues wiring. But I need a way to prevent. Any advice?

Also a side note anyone who uses 450s how hot does the heat sink get. mine are usually warm coming out of an event but tonight they were pretty hot and i only ran them at a quarter like i usually do for this size event. Ther less than a year old. I'm assuming this isn't a problem just curious.
 
Where both connected in the same circuit? What is your signal chain ? It could be the venue plugged something in the circuit and you had the problem. Now regarding the temperature, are you running them through a sound processor like the BBE or does your mixer have WOW or special settings for sound? T

The Mackies don't like those processors. Even with the clip lights not going off you can overdrive them with such processors. Finally how many people, venue type and type of music played?
 
Also complete the above questions for svo... but here is something you can try when you get the chance... Work backwards approach. Take your speakers and set them up on a pole, no xlr's connected, power them to 1/4 throttle on the gain :) what buttons are pushed in? Does the buzz exist? Was the buzz equal on both speakers the other night?

Let us know how it goes up to that step and we can then work better to solve the problems.
 
I'm thinking DJ Gray had this issue recently...
 
Where both connected in the same circuit? What is your signal chain ? It could be the venue plugged something in the circuit and you had the problem. Now regarding the temperature, are you running them through a sound processor like the BBE or does your mixer have WOW or special settings for sound? T

The Mackies don't like those processors. Even with the clip lights not going off you can overdrive them with such processors. Finally how many people, venue type and type of music played?

Both were connected to the same circuit.

The signal went out of the mixer left to one Mackie and out off the mixer right to the other. I was not using any signal processors last night and no WOW. There was dancing for about 2 hours at the end but the system was used for PA for about 4 hours before that. I was driving a decent amount of bass through the speakers during the dancing though as I didn't bring subs. So that might have accounted for the heat?

Bounce I will try what you suggested and post my results. Thanks for the help guys.
 
Ok I just had time to sit down and test things. I't seems to be happening only when connected to my mixer. I turned on the mackie by itself. Than connect the mixer and as soon as I did so the "refrigorator hum" came back. My mixer I'm using now doesn't have xlr outs so I use a 1/4 inch to XLR cable to connect the Mackie could this be part of my problem?
 
Okay Tim, try with your mixer off, any hum? try a different cable, also try every knob down, every slider down, eq's at normal, pan's at normal, graphic eq at center, aux's off, phantom pwr on, just start with a clean board and see if it still does that. Also make sure your plugging your mackies into the same power as your mixer :)

It is safe to say it isn't the mackies at this point... Also you might wanna get a continuity tester and test the pins on your xlr's (they should be numbered 1-2-3) Go pin for pin and verify that you have a good cable... Also a good cable tester (ask ben) can do wonders for ya :)
 
What mixer make and model?

In situation such as this, there is a tedious yet foolproof way of isolating unusual noise conditions of any kind.

Disconnect everything; cables and all, from everything (speaker, mixer, CD players, laptops, ancillary stuff such as BBEs, eq, etc).

Proceed carefully and thoroughly with one piece, one cable at a time. Also be forewarned that some so called power conditioners do condition the AC but do absolutely nothing for induced noise.

Another common error is mixer to cable lengths. Some folks have 25-50 feet cables to go 10 foot. Being neat, they coil the excess cables length and secure it with Velcro or cable tie. Not a good idea. Excess coiled cable can act like a UHF antenna and any ungrounded light dimmers in the building, spurious TVI and RFI, may come booming through but not at every facility (which can be maddening until fixed)

Now then fun begins.

Turn on the powered speaker. Anything?
If not, then plug in the connecting cable (nothing connected on the other end). Anything?

If not, plug the other cable end into the mixer (turned off, all gains to zero). Anything?

If, not, turn the mixer on. Anything?

If not, increase the mixer master gains slowly. Anything?

If not, plug in the cables to your wired or wireless mic. Anything?

If not, plug the cable into the mic or the mice receiver. Anything?

If not, turn on the mic or mic receiver. Anything?

Now start messing with the master mixer outputs at a comfortable level and increase the mic receiver. Anything?

If not, slowly increase the mic gain on your mixer. Anything?

If not, start plugging in the cable for your media source inputs, then plug the cables into the media sources, then turn the sources on, then adjust mixer levels.

This method is slow but it isolates every problem, one at a time. In your case, what if there is more then one problem? That's why it is highly suggested to approach noise problem isolation one step at a time.

Hope this helps. It's one of the best ways to be 99.9% sure.
 
Ok. Bounce I tryed connecting the Mackie to the same power source as the mixer and the hum I had been getting went away. Know their is still a little noise but I can eliminate that using the method described by Cap and its really not that much. So pluggin into the same power source eliminates the majority of the problem. What does this mean? The power source my mixer was in was through a fruman and into the wall. Does this mean my Mackies need to be through my furman? Or just on that line. What would be the reason for having noise on seperate lines and not on the same?
 
The lack of subs explains the heat.
 
Ok. Bounce I tryed connecting the Mackie to the same power source as the mixer and the hum I had been getting went away. Know their is still a little noise but I can eliminate that using the method described by Cap and its really not that much. So pluggin into the same power source eliminates the majority of the problem. What does this mean? The power source my mixer was in was through a fruman and into the wall. Does this mean my Mackies need to be through my furman? Or just on that line. What would be the reason for having noise on seperate lines and not on the same?
What you described is a typical example of grounding issues... In live sound it is crucial that your sound system is connected to a shared ground, in most simple cases the same wall socket, or power strip, doing so forces your sound equipment to stay hum free, also using an balanced xlr, which uses the 3rd pin which is the shield of the cable to balance the static electricity on a sound system. This is exactly why you DO NOT use a plug adapter that removes the ground. Also to prevent tripping of a breaker be sure to put your lighting on a separate circuit, DMX doesn't have near the amount of line static problems as audio. The Mackies will have some amount of slightly noticeable line noise, pretty much every sound system does, doesn't matter if it is passive or active. Glad we could help solve your problem :)
 
Thanks bounce.
I'll have to look into upgrading my mixer so I have balanced connections to the Mackies. But for now my problem is solved thanks to everyone who helped.
 
I've been reading along to help with a very similiar problem. I've also noticed that I got a lot of noise when I switched to new rack and the metal contact (I was using a custom wood rack before) was causing noise. I used electrical tape and nylon washers to eliminate most of the buzz, but now I still have a ground loop with my dual CD player. Should I buy a hum eliminator to place between the CD player and my mixer? In a quiet room I can actually hear the buzz increase when I even touch the buttons on my CD control panel. I have all my audio components running off the same circuit.

I also know that as DJ's we are WAY more aware of that noise than anyone else in the world, I just want a noise free system, and won't rest until I achieve it! :sqwink:
 
Tim:

I didn't read through the whole thread yet so I don't know what everybody else said. I usually do when there are multiple posts but there was one thing that caugt my attention that may be the source of your heat problems.

You said you had the Mackie 450's at 1/4 power. The question that came to mind was what were your mixer settings? You could still be overdriving the amp, causing it to put out more heat. Even though you may not need all the power, set the amps at max and use your mixer trim to regulate the sound.

Since the 450 has thermal protection, if it gets too hot on you it might shut down and then you'd have to wait for it to cool down.
 
I've been reading along to help with a very similiar problem. I've also noticed that I got a lot of noise when I switched to new rack and the metal contact (I was using a custom wood rack before) was causing noise. I used electrical tape and nylon washers to eliminate most of the buzz, but now I still have a ground loop with my dual CD player. Should I buy a hum eliminator to place between the CD player and my mixer? In a quiet room I can actually hear the buzz increase when I even touch the buttons on my CD control panel. I have all my audio components running off the same circuit.

I also know that as DJ's we are WAY more aware of that noise than anyone else in the world, I just want a noise free system, and won't rest until I achieve it! :sqwink:

hmmm
high quality gold RCA cables for audio?
high quality adapters?
Have you connected LCD projector to the same power supply as sound?
Have you tried unplugging power supply to the laptop? Does the cord have an EMI resistor on it? (plastic bubble thing encasing cord)

Are you one hundred percent sure its the mixer and not an outboard wireless system inducing noise?
Are your power cables inside your gut box coiled or wrapped in a figure 8?

some thoughts....
 
J - right now I'm down to thinking it's still has a tad to do with metal contact...still need to tape front rails and probably some looping in the box with excess cords....so figure 8 not loop? I also noticed a bit of extra sound when wireless mic is on. Reciever is sitting on rubber pads on top of power conditioner, but could it be picking up frequencies from looped cords?
 
J - right now I'm down to thinking it's still has a tad to do with metal contact...still need to tape front rails and probably some looping in the box with excess cords....so figure 8 not loop? I also noticed a bit of extra sound when wireless mic is on. Reciever is sitting on rubber pads on top of power conditioner, but could it be picking up frequencies from looped cords?

Try the other route. Metal on metal everywhere you can....
hmm....got me thinking...
 
Try the other route. Metal on metal everywhere you can....
hmm....got me thinking...

Tried that, huge buzz coming from CDN95 controller...75% of the buzz left with electrical tape under top rack. Need to isolate the rest of the noise.

by the way, picking up the moving heads Monday!!!!!!!