Need DMX Controller Feedback And Advice.

To many ads? Support ODJT and see no ads!
K

Kirby Ball

Guest
Ok, I have slowly started my venture into DMX lighting by purchasing the Chauvet Oceana (should have it in my hands on Thursday or Friday, I hope).

I will use it without the DMX controller in the beginning and add it to my selection of spin and pukes.

What I'd like to get is some feedback on DMX controllers that you are currently using or have used in the past.

I don't think I want to get the "cheapest" nor the most "expensive". I just want a good reliable mid-level controller that will do the job and not put me too far in debt.

Any feedback will be greatly appreciated.

Thanks in advance. :sqbiggrin:


Kirby
 
Steve: Have you (or anyone else) personally used the Weidamark controller?

I will appreciate any feedback and information that anyone can provide on this brand or any others that are out there.


Thanks!

Kirby
 
I'll put another requirement into the mix,,,, Must be EXTREMLEY user friendly..
 
That Weidamark looks real nice for $109..... I paid a $100 for mine, used..... and I haven't used it yet, but I have read Tyrone's book! Mine is a Chauvet, I think.
 
DMX Operator Pro.

Left side will do 8 DMX addresses with up to 16 channels each.
Right Side will do 8 DMX addresses for PAR cans. (gotta have DMX dimmer packs.)

96 scenes for DMX and something close to that for pars.

Mine has been a beauty for 3 years....

attached is the manual
 

Attachments

  • DMX-OPERATOR-PRO-REV1204.pdf
    371.4 KB · Views: 6
I haven't used the Pro...

...but, I've used a few others. Once you learn DMX, they are all pretty much the same, except for features. One will control 12 fixtures with 240 total scenes... one will control 8 fixtures with 400 total scenes... etc. etc.

DMX is DMX everywhere. Once you know the basics, you shouldn't have trouble with any of them. I like the two sided features of the Pro (from the manual). It allows you to use conventional pars, with DMX dimmer packs, and regular DMX fixtures on one controller... nice feature.

I use the 12 fixture controllers and I also use the Chauvet DMX 6. Same pricipals... just different scene numbers , channels and fixture numbers. They program the same. CHUCK, I wish I could say they were user firendly... but without programming abilities, and understanding DMX, they are all difficult. Come see me in Vegas... I'll make it VERY EASY for you... promise!

FLASH... there is a brand new controller out that has at least two "DMX out" ports on the back, which will allow you to go in two different directions with your signal without the use of a splitter.

I am working on the Show XPress, which is basically the same, but a higher learning curve at first. The program does a lot of the work for you, like setting addresses and moving your fixtures (in 3D mode) without them being hooked up.

My seminar in Vegas will give you DETAILED instructions on how to program anything. I'm putting together a Power Point presentation as I write this, with lots of good information on the hardware controllers. "Even a caveman can do it".
 
Thanks for everyone's input so-far, it's great to get solid feed-back from the users of DMX controllers.

Tyrone: I have your booklet and I'm sure it will make more sense once I have a controller and some lights to play around with.....I hope..:sqconfused: I sure wish that I could be there in Vegas to experience your seminar in person.

Again I truly appreciate everyone's help and if anyone has anything else to add or if you think of anything else that I should consider...Please post..

Thanks to you all out there.....

Kirby "DMX Fever Is Getting Worse" Ball
 
The only limitation with the Chauvet I find is the number of chase buttons...6...I'd like about two dozen more, aloow in you to program your ligting specigically. For instance I have mt pars prtogrammed on one chase...al 4 at once, patterns of two on a secoind chase, dimmed on a 3rd..I'd like the freedom to use chases to have them strobe...so everything is at a finger tip..this would give you the ability to say, set a chase for an acrobat simply to have the lights sweep.

I recognize all this is available with banks and scenes, but you cannot easily go from say bank 2 to bank 12 *(you have to scroll).

Those with the pc/usb solution......YBDJ.....are you limited in the nuber of chases...can you combine chases and or banks...Can you "one click" from one bank/chase to another instantly?

Check this.....

http://www.pcdj.com/products/dmx.asp

Not cheap - about $450.00
 
The only limitation with the Chauvet I find is the number of chase buttons...6...I'd like about two dozen more, aloow in you to program your ligting specigically. For instance I have mt pars prtogrammed on one chase...al 4 at once, patterns of two on a secoind chase, dimmed on a 3rd..I'd like the freedom to use chases to have them strobe...so everything is at a finger tip..this would give you the ability to say, set a chase for an acrobat simply to have the lights sweep.

I recognize all this is available with banks and scenes, but you cannot easily go from say bank 2 to bank 12 *(you have to scroll).

Those with the pc/usb solution......YBDJ.....are you limited in the nuber of chases...can you combine chases and or banks...Can you "one click" from one bank/chase to another instantly?

Check this.....

http://www.pcdj.com/products/dmx.asp

Not cheap - about $450.00


Steve: Cool, thanks for giving me something else to consider (chase buttons).

Yup, $450.00 will be a little more than I want to budget for a controller at this time. Now, if I hadn't spent all that money on my "spin and pukes"...Oh well.. :D

Appreciate the continued feedback! :thumbsup:
 
Kirby - The USB/PC solution may be the cheapest and most effective (unless you need to buy a laptop)... Freestyler is a free software package. The Usb box is about 50 bucks.....Hopefully we'll hear from those using it....

The Wiedamark unit has 48 chases
 
I'm open to all suggestions from anyone with their experiences with DMX controllers and keeping an open mind on the various possibilities.

Darn that Tyrone for giving us all DMX fever! :sqcool: :sqlaugh:

Again, I truly appreciate your feedback!

Kirby
 
Freestyler is a fully featured software, and as stated, free... several of us here use it, and I assure you... hardware controllers are a waste of time now that software is so readily available... takes a small amount of setup (less than with a hardware controller) and you're designing lightshows that will impress yourself and others...

freestyler is just as powerful as light jockey, compuware, show designer, etc...

and best of all? Free!

pick it up, you won't be sorry!

unlimited chases, instant recall of scenes, cues, and pre programmed shapes and such... it's a beautiful thing.
 
Freestyler is a fully featured software, and as stated, free... several of us here use it, and I assure you... hardware controllers are a waste of time now that software is so readily available... takes a small amount of setup (less than with a hardware controller) and you're designing lightshows that will impress yourself and others...

freestyler is just as powerful as light jockey, compuware, show designer, etc...

and best of all? Free!

pick it up, you won't be sorry!

unlimited chases, instant recall of scenes, cues, and pre programmed shapes and such... it's a beautiful thing.


Would you be running this on a separate laptop?

Thanks
 
Steve L.....Is the Entec box I mentioned above what i need..

WRT the software.....I want to be able to run multiple chases at once (ie. LED pars, then Oceana.

Can you pick and run multiple scenes.....LED pars, then Acrobats strobing, etc....

If it can do all this, there may be a used controller going up for sale....

Thanks...
 
the enntec box can be used, but you'll need a 5 pin to 3 pin adaptor....

the most common dongle people use is the velleman open dmx controller... but any of them will work...

yes, they do run off sound once you set them up to do so....

also, I run My dmx software right along with virtual dj, roxbox, and recording software....

I know some people have problems, but I've been multitasking this stuff for years with no issues... it's not very cpu intensive unless you're running hundreds of fixtures...

however, if you want it on another machine, you'll be happy to know it runs like a champ on a 400 mhz pIII laptop.... you can practically pick one of those up at the goodwill for $25.00

all of the people trying to push their $400.00 DMX software packages will speak badly of freestyler, but at the end of the day, it's easier to use, and free... they hate the free part...

try it and make your own decision.... then download pcdj dmx, lightjockey, and other apps to compare.... you'll see what I mean....

-Steve