Speaker Hiss

To many ads? Support ODJT and see no ads!
Greets, Brother Gray. :)

Let's do some basic troubleshooting. First, power your cabs up with no input cables connected. Is the hiss present? If yes, it's an issue with the cab(s).

If no hiss is present, connect the XLR input cables (other end of cables not connected). Does this cause hiss? If so, it's a cable issue. If not, let's move to the input.

Connect up to your output from processing with all processors powered down. Is there hiss? If so, try isolating each component, one at a time, all powered down.

If no hiss is present, try powering up processing one at a time to isolate the hiss.

Several things can cause system hiss, tarnished TRS patch plugs being one of the more notorious. With your system powered up, no input, try wiggling or twisting patch cables to see if you notice any difference. If you hear pops or intermittent hiss, clean the plugs and go from there.

Let me know what you find out. :)


Wolfie......
Well it failed the first test........When I disconnected the Audio Inputs and turned on the speakers the hiss was there......:sqfrown:
One other thing I did notice was as per Hiredpowers recommendation I checked the Mic/Line switch on each of the speakers and the switch for the mic/line does not extend through the surface of the Cab I tried pushing in and it would not set in anything but the extended position, it would not set down.....these speakers have always had a hiss...as a newbie I did not know this was not the way they were to be ??????:sqembarrassed: What next ????
 
On your Eon, check the mic/line switch to make sure it is in the up position (line).

Sometimes this switch can get bumped (depressed) to mic and the input is very sensitive causing a hum like you describe when the volume is turned up.

See image below:


I checked the switch and it does not come through the surface of the Cab...it's recessed, when I tried poking with a screwdriver to see if it would set down,..it wouldn't it is set in the extended position.......
 
Well... it's been isolated to the speakers. That's a good start. Now you know where the hiss is coming from. :)

I don't own active cabs but the passives we have contain below deck switches on the crossover plates. They're used for bi-amping or full range settings.

The switches are deliberately mounted below deck so that they aren't likely to be moved accidentally. A small screwdriver is all that's needed to move the switches. Ours actually move side to side. Or up and down, can't recall which. But they don't push in and push out.

If the switches on your cabinets can't be moved for some reason, they should be repaired.
 
Wolfie......
Well it failed the first test........When I disconnected the Audio Inputs and turned on the speakers the hiss was there......:sqfrown:
One other thing I did notice was as per Hiredpowers recommendation I checked the Mic/Line switch on each of the speakers and the switch for the mic/line does not extend through the surface of the Cab I tried pushing in and it would not set in anything but the extended position, it would not set down.....these speakers have always had a hiss...as a newbie I did not know this was not the way they were to be ??????:sqembarrassed: What next ????

Do a Ground lift test on the power cable, just to see.... Then send them in for repair!
 
Well... it's been isolated to the speakers. That's a good start. Now you know where the hiss is coming from. :)

I don't own active cabs but the passives we have contain below deck switches on the crossover plates. They're used for bi-amping or full range settings.

The switches are deliberately mounted below deck so that they aren't likely to be moved accidentally. A small screwdriver is all that's needed to move the switches. Ours actually move side to side. Or up and down, can't recall which. But they don't push in and push out.

If the switches on your cabinets can't be moved for some reason, they should be repaired.

This "below deck" switch means....?? on the back of the speaker ?? Is the switch labeled ?? Could it be the power strip I'm using....??:sqconfused:
 
Does this happen at every venue or just some? If it's just some, is it only the venues that have dimmable lights? If so, that may be the problem.

No it dosen't happen at all events, a lot of the venues I play at have Dimmable lights. I also have those at the house where the hiss is noticeable.....Our house has Aluminum wiring and I'm not sure if that is relavent or not??
 
Our house has Aluminum wiring and I'm not sure if that is relavent or not??

Correct me if I'm wrong, but I believe aluminum wiring should be replaced whenever possible as the ends of it can corrode or shrink or something, leading to the wiring behind your outlets arcing and starting a fire.

Something to definitely look into if you're not aware already. Maybe I'm off on that, but your post threw a big red light up for me. :sqconfused:
 
Correct me if I'm wrong, but I believe aluminum wiring should be replaced whenever possible as the ends of it can corrode or shrink or something, leading to the wiring behind your outlets arcing and starting a fire.

Something to definitely look into if you're not aware already. Maybe I'm off on that, but your post threw a big red light up for me. :sqconfused:

Thanks for your concern. From a safety standpoint We had the problem taken care of 15 years ago. The Electrican neutralized the Fire/destructive nature of the situation. I have since had Electricans review the wiring with the same result. What I don't know is whether that would affect the grounding ability of the circuit?
 
Well, copper is the better conductor, but I would think as long as the ground conductor was in place and connected that you'd be fine.

Try using a cheater to power the speaker (and any other equipment) to rule it out.

I'm not sure if you'd want to put each item on its' own cheater, or if you could just use a power strip with a cheater. Using a power strip would still leave the ground between each item on the strip, so probably use individuals.
 
Wolfie wrote:
The switches are deliberately mounted below deck so that they aren't likely to be moved accidentally. A small screwdriver is all that's needed to move the switches. Ours actually move side to side. Or up and down, can't recall which. But they don't push in and push out.

If the switches on your cabinets can't be moved for some reason, they should be repaired.

I'll se if I can find these switches and I'll let you know what I find...Thanks Wolfie
 
Correct me if I'm wrong, but I believe aluminum wiring should be replaced whenever possible as the ends of it can corrode or shrink or something, leading to the wiring behind your outlets arcing and starting a fire.

Something to definitely look into if you're not aware already. Maybe I'm off on that, but your post threw a big red light up for me. :sqconfused:

Here in Florida that code is grandfathered, meaning if it's been done, it's fine.. they'll give you hell from the city if you connect it to copper wiring and don't do it right.


DJ Gray, most likely the humming is coming from the dimmers. I suggest buying HumX, you'll love it.

As far as hissing goes, what mixer do you have again? And what wires do you use?
 
I checked the switch and it does not come through the surface of the Cab...it's recessed, when I tried poking with a screwdriver to see if it would set down,..it wouldn't it is set in the extended position.......

My money is on a bad mic/line switch. If it doesn't move up and down, I believe it is stuck in "mic" position.

Try this:

Plug a microphone with an xlr cable directly into one of your eons and slowly turn up the volume (be careful not to get the mic too close/feedback).

If you do not have your hiss/humming sound while speaking into the mic past 12 o'clock, the switch is stuck in the "mic" position.
 
Here in Florida that code is grandfathered, meaning if it's been done, it's fine.. they'll give you hell from the city if you connect it to copper wiring and don't do it right.


DJ Gray, most likely the humming is coming from the dimmers. I suggest buying HumX, you'll love it.

As far as hissing goes, what mixer do you have again? And what wires do you use?


I have a numark 1200 mixer and Monster XLR cables
 
My money is on a bad mic/line switch. If it doesn't move up and down, I believe it is stuck in "mic" position.

Try this:

Plug a microphone with an xlr cable directly into one of your eons and slowly turn up the volume (be careful not to get the mic too close/feedback).

If you do not have your hiss/humming sound while speaking into the mic past 12 o'clock, the switch is stuck in the "mic" position.


I will try that......and let you know