I hate this sound!
Curious... why did you have the inverts activated?
It seemed to improve the bass response?
I hate this sound!
Curious... why did you have the inverts activated?
Greets, Brother Gray.
Let's do some basic troubleshooting. First, power your cabs up with no input cables connected. Is the hiss present? If yes, it's an issue with the cab(s).
If no hiss is present, connect the XLR input cables (other end of cables not connected). Does this cause hiss? If so, it's a cable issue. If not, let's move to the input.
Connect up to your output from processing with all processors powered down. Is there hiss? If so, try isolating each component, one at a time, all powered down.
If no hiss is present, try powering up processing one at a time to isolate the hiss.
Several things can cause system hiss, tarnished TRS patch plugs being one of the more notorious. With your system powered up, no input, try wiggling or twisting patch cables to see if you notice any difference. If you hear pops or intermittent hiss, clean the plugs and go from there.
Let me know what you find out.![]()
On your Eon, check the mic/line switch to make sure it is in the up position (line).
Sometimes this switch can get bumped (depressed) to mic and the input is very sensitive causing a hum like you describe when the volume is turned up.
See image below:
Wolfie......
Well it failed the first test........When I disconnected the Audio Inputs and turned on the speakers the hiss was there......![]()
One other thing I did notice was as per Hiredpowers recommendation I checked the Mic/Line switch on each of the speakers and the switch for the mic/line does not extend through the surface of the Cab I tried pushing in and it would not set in anything but the extended position, it would not set down.....these speakers have always had a hiss...as a newbie I did not know this was not the way they were to be ??????:sqembarrassed: What next ????
Do a Ground lift test on the power cable, just to see.... Then send them in for repair!
Do a Ground lift test on the power cable, just to see.... Then send them in for repair!
Well... it's been isolated to the speakers. That's a good start. Now you know where the hiss is coming from.
I don't own active cabs but the passives we have contain below deck switches on the crossover plates. They're used for bi-amping or full range settings.
The switches are deliberately mounted below deck so that they aren't likely to be moved accidentally. A small screwdriver is all that's needed to move the switches. Ours actually move side to side. Or up and down, can't recall which. But they don't push in and push out.
If the switches on your cabinets can't be moved for some reason, they should be repaired.
(Plug it into a cheater -- the 3 prong to 2 prong adapter for ungrounded outlets)
Does this happen at every venue or just some? If it's just some, is it only the venues that have dimmable lights? If so, that may be the problem.
Our house has Aluminum wiring and I'm not sure if that is relavent or not??
Correct me if I'm wrong, but I believe aluminum wiring should be replaced whenever possible as the ends of it can corrode or shrink or something, leading to the wiring behind your outlets arcing and starting a fire.
Something to definitely look into if you're not aware already. Maybe I'm off on that, but your post threw a big red light up for me. :sqconfused:
The switches are deliberately mounted below deck so that they aren't likely to be moved accidentally. A small screwdriver is all that's needed to move the switches. Ours actually move side to side. Or up and down, can't recall which. But they don't push in and push out.
If the switches on your cabinets can't be moved for some reason, they should be repaired.
Correct me if I'm wrong, but I believe aluminum wiring should be replaced whenever possible as the ends of it can corrode or shrink or something, leading to the wiring behind your outlets arcing and starting a fire.
Something to definitely look into if you're not aware already. Maybe I'm off on that, but your post threw a big red light up for me. :sqconfused:
I checked the switch and it does not come through the surface of the Cab...it's recessed, when I tried poking with a screwdriver to see if it would set down,..it wouldn't it is set in the extended position.......
Here in Florida that code is grandfathered, meaning if it's been done, it's fine.. they'll give you hell from the city if you connect it to copper wiring and don't do it right.
DJ Gray, most likely the humming is coming from the dimmers. I suggest buying HumX, you'll love it.
As far as hissing goes, what mixer do you have again? And what wires do you use?
My money is on a bad mic/line switch. If it doesn't move up and down, I believe it is stuck in "mic" position.
Try this:
Plug a microphone with an xlr cable directly into one of your eons and slowly turn up the volume (be careful not to get the mic too close/feedback).
If you do not have your hiss/humming sound while speaking into the mic past 12 o'clock, the switch is stuck in the "mic" position.