So you'd like to build a professional PA system...

To many ads? Support ODJT and see no ads!

Fred Wright

Administrator
Staff member
Aug 7, 2006
12,741
1,015
68
Delaware, USA
www.nwedj.com
Let's begin at the ending, so to speak. Speaker systems are your first consideration by far.

You'll need to determine venue size and average number of guests at your shows before you decide upon speaker system purchases. Whether you wish to go active or passive, you must match your speaker systems to the venues you will be working in. Remember, it is always better to have too much than too little.

When comparing speaker systems, look at the sensitivity rating. This number basically tells you how efficient the systems are. The higher the number, the more SPL or sound pressure you will get with a given amount of input amp power. You want the highest sensitivity rating.

By their nature, sub cabinets often carry lower sensitivity ratings than full range systems. So don't let this deter you from investing in a sub cabinet.

If you'll be working with active cabinets, you may disregard the following. Now that you've decided upon your speaker system needs, let's look at amps. Passive prosound systems require amplifier headroom to function properly. I prefer 100% amp headroom but that's just me. Amp headroom is basically defined as output dissipation that is capable of going above the speaker system's rating.

For example, if your speaker system is rated for 400 watts RMS @ 8 ohms and your amp is capable of 500 watts RMS @ 8 ohms, you have 100 watts of headroom. Headroom becomes more important as the frequency response goes lower. You won't need much amp headroom for mid-tops and vocals. You should provide plenty of amp headroom for a sub cabinet, though.

Be sure to plan your system purchases with growth in mind. If you cannot afford the full monte at once (and who can?), start small with one amp and cabinet set then add to it later. Buy things today that you will still be able to use ten years from today. If you don't absolutely need it today, let it wait.

Thoughts?
 
So, here's what happened to me... Pro advise please...

Two weeks ago, a band that showed up at one of our local clubs without any gear (they had been told the club had a system in place). It didn't.

They had to scramble, and contacted me. I had several big JBL speakers (and my K-2 amps that I've never used yet) , but they needed a PA in order to get all of their sound out to the speakers. I showed them my smaller DJ rack which only had my little DJ mixer running to a crossover and two smaller amps, and they said they couldn't use it. So, what actually is a PA in terms of putting a band into a sound mode? Is it the same or different than a sound board?

Is a PA basically a "big" mixer with bigger inputs & outputs? I am assuming you can put in mics, guitars, and keyboards, and have them come out one output into the amps... is this correct? How many inputs should a PA have for a small band?

Reason I ask, is I'm considering buying a PA from Ben if this is the case. How about a little education on the path of a music signal (whether it's a computer mp3 or a band)... remember, I'm a novice when it comes to sound systems, so take it easy. Tell me what I'd need for putting a four piece band into action as long as I have speakers and amps. And, what kind of cables?

Oh, also... does a PA have to have amps itself (or a power supply) of some sort, or can it be just a mixer box? If so, how much amplification would I need?

BTW: My BIG amp rack (three K-2's... new and untested as of this writing) is wired with a crossover. There is only one right and left XLR input to this rack. Therefor, I assume a PA has only one output that goes into one input on this amp rack???

Oh, one last question: when I get ready to hook up my big speakers from the K-2 amp rack, what kind of an input (cables specifically) do I need from my little mixer in order to feed it into the K-2 rack which has XLR inputs? Is there such a cable as an RCA into and XLR? Or, maybe my mixer has a 1/4 inch output... not sure.
 
Two weeks ago, a band that showed up at one of our local clubs without any gear (they had been told the club had a system in place). It didn't.

They had to scramble, and contacted me. I had several big JBL speakers (and my K-2 amps that I've never used yet) , but they needed a PA in order to get all of their sound out to the speakers. I showed them my smaller DJ rack which only had my little DJ mixer running to a crossover and two smaller amps, and they said they couldn't use it. So, what actually is a PA in terms of putting a band into a sound mode? Is it the same or different than a sound board?

Is a PA basically a "big" mixer with bigger inputs & outputs? I am assuming you can put in mics, guitars, and keyboards, and have them come out one output into the amps... is this correct? How many inputs should a PA have for a small band?

Reason I ask, is I'm considering buying a PA from Ben if this is the case. How about a little education on the path of a music signal (whether it's a computer mp3 or a band)... remember, I'm a novice when it comes to sound systems, so take it easy. Tell me what I'd need for putting a four piece band into action as long as I have speakers and amps. And, what kind of cables?

Oh, also... does a PA have to have amps itself (or a power supply) of some sort, or can it be just a mixer box? If so, how much amplification would I need?

BTW: My BIG amp rack (three K-2's... new and untested as of this writing) is wired with a crossover. There is only one right and left XLR input to this rack. Therefor, I assume a PA has only one output that goes into one input on this amp rack???

Oh, one last question: when I get ready to hook up my big speakers from the K-2 amp rack, what kind of an input (cables specifically) do I need from my little mixer in order to feed it into the K-2 rack which has XLR inputs? Is there such a cable as an RCA into and XLR? Or, maybe my mixer has a 1/4 inch output... not sure.

Geez, where to begin in answering...........

Ty,

First of all, the only thing I can describe to you is what I have encountered in my years of club dj'ing and mixing live theatre and club bands. I consider myself a novice in this matter, so what I may have to say may be disputed by others. But, here we go........

To begin with, even the smallest of clubs that provide sound systems for bands usually have at the very least, a 24 channel mixing board with 24 lines in/4 lines out. At our club, we provide the following:

(1) 32 channel Yamaha board on the stage for the stage monitor mix

(2) QSC amps for the dual 18" JBL bass bins

(2) QSC amps for the 4 flown JBL house monitors

(2) QSC amps for the 4 stage monitors

(1) 32 Channel Allen & Heath F.O.H. mixing board

One of the amp cabinets also contains:
(1) Ashly active cross-over
(1) DOD stereo EQ

All JBL stage monitors are fed with Neutrik connector cables.

The majority of the instruments the band members use are amp'd and amps are mic'd. This is what you will feed into the snake. The snake feeds into the mixing board, the board output feeds the EQ, the EQ out to the input of the cross-over, the cross-over out to the amps.

For a 4 piece band, with drums, a rythym guitar, a lead guitar and a bass guitar, you can bet that every one of the 24 to 32 channels is going to be used. It's important to keep in mind too, that mics will take up a considerable number of those inputs. The majority of popular mixing boards provide both XLR and 1/4" TRS inputs. A good XLR snake direct box for stage use is recommended as well. This will cut down on cable clutter.

Many of today's bands use in-ear monitors, so an output needs to be considered for that possibility.

This is just the tip of the iceburg. There is so much more to providing sound for a club band that I can't even begin to go into.

Try this link for a beginners guide to mixing live sound:

http://www.recordingreview.com/arti...rs-and-Mixing-Consoles/Analog-Mixers-101.html

Yamaha also provides some interesting food for thought here:

https://www.yamaha.com/yamahavgn/CD...,,CNTID%253D64876%2526CTID%253D230600,00.html

And finally:

http://teachers.edenpr.org/~benanderson/Microphones and Sound System Basics.htm

As I said previously, this is just the tip of the iceburg. I hope what small amount of info I have given has been helpful.

Cheers!

Greg.
 
Geez, where to begin in answering...........

Ty,

First of all, the only thing I can describe to you is what I have encountered in my years of club dj'ing and mixing live theatre and club bands. I consider myself a novice in this matter, so what I may have to say may be disputed by others. But, here we go........

To begin with, even the smallest of clubs that provide sound systems for bands usually have at the very least, a 24 channel mixing board with 24 lines in/4 lines out. At our club, we provide the following:

(1) 32 channel Yamaha board on the stage for the stage monitor mix

(2) QSC amps for the dual 18" JBL bass bins

(2) QSC amps for the 4 flown JBL house monitors

(2) QSC amps for the 4 stage monitors

(1) 32 Channel Allen & Heath F.O.H. mixing board

One of the amp cabinets also contains:
(1) Ashly active cross-over
(1) DOD stereo EQ

All JBL stage monitors are fed with Neutrik connector cables.

The majority of the instruments the band members use are amp'd and amps are mic'd. This is what you will feed into the snake. The snake feeds into the mixing board, the board output feeds the EQ, the EQ out to the input of the cross-over, the cross-over out to the amps.

For a 4 piece band, with drums, a rythym guitar, a lead guitar and a bass guitar, you can bet that every one of the 24 to 32 channels is going to be used. It's important to keep in mind too, that mics will take up a considerable number of those inputs. The majority of popular mixing boards provide both XLR and 1/4" TRS inputs. A good XLR snake direct box for stage use is recommended as well. This will cut down on cable clutter.

Many of today's bands use in-ear monitors, so an output needs to be considered for that possibility.

This is just the tip of the iceburg. There is so much more to providing sound for a club band that I can't even begin to go into.

Try this link for a beginners guide to mixing live sound:

http://www.recordingreview.com/arti...rs-and-Mixing-Consoles/Analog-Mixers-101.html

Yamaha also provides some interesting food for thought here:

https://www.yamaha.com/yamahavgn/CD...,,CNTID%253D64876%2526CTID%253D230600,00.html

And finally:

http://teachers.edenpr.org/~benanderson/Microphones and Sound System Basics.htm

As I said previously, this is just the tip of the iceburg. I hope what small amount of info I have given has been helpful.

Cheers!

Greg.

Don't forget Mics
Stage splitter to accommodate the monitor mixer and the FOH snake
Snake to FOH
Gates/Compressors/Limiter/echos/delays/reverbs for mics....

And DBX DRIVERACK BABY!!!!
 
I said "go easy"...

The first few lines were way over my head already... I'm not interested in using a sound board if it's different than a PA. I'm also not interested in hooking up Pink Floyd.

I was under the impression that a PA was a two foot square box with several inputs and one output. Several channels with control knobs that control each channel. I also thought that some PA's had their own amps and some did not.

Let's try it this way, and let me know if I'm wrong on anything. I have a computer with a mini jack for earphones. I take this signal and put it into a channel of my four channel DJ mixer with an adapter cable that has 1/8 mini on one end, and two RCA's on the other. I then feed this to my crossover which separates the signal into highs and lows, then feeds it to both of my amps. My amps then feed it to my speakers which I control from my mixer board.

Now, if I had this PA box, could I feed my computer signal into this (along with a guitar, and keyboard... and whatever else I wanted), and a couple of microphones (just like a mixer board). Could I then control the levels with the PA box and sent it to my amp rack with the crossover already build in and feed it to my speakers?

The good side of my questions... now I really understand the "frustration" of all our newbies.
 
Sorry Tyrone...

PA is a term used for the word "Public Address". Its a very loose term
Almost as loose as Chuck...
You use a PA already for your DJ and Karaoke. If its gotta microphone and speakers, its a PA.
You use a 2 channel mixer or something similar, and you probably can flip 2 sources on each channel.

All a 32 channel mixer is used for is to accommodate multiple inputs from various sources.
So say:
1 is your left cd player
2 could be your right cd player
3 could be your computer
4 could be your ipod
(actually, you would just run your outs from your mixer to channel 1 and 2 of the big board if you wanted.....or 31 and 32, it really doesn't matter.)

THEN


5 could be the lead singer
6 could the the backup singer
7 could be the vocal mic for the drummer
8 could be the bass
9 could be lead guitar
10 could be rhythm guitar
11 could be keyboard
12 is Kick
13 is snare
14 is hi-tom
15 is mid-tom
16 is low-tom
17 is overhead mic for cymbals
18 is hi-hat


and on and on
A 32 channel snake is a box on stage that accepts the inputs from either the instruments or mics and sends all 32 cables as one BIG cable to the Mixer up front of the house or "FOH". Then the ends plug into the mixer. There are usually "sends" that travel in the same bundle of wires to route the main outputs of the mixer to the amp racks by your speakers on stage. A snake is a 2 way device. 32 in, and anywhere from 4 to 8 or more outs.....

WATCH THIS VIDEO


who wants to explain the next chunk?
 
OK...

I'm going to ask this question, then go back and look at the video, so if it's already answered... sorry.

I'm posting two pictures. Are both these devices the same? Is one better to use than the other? Is a board overkill for what I need? Reason I ask, is the band in my above original question, rented a "box" mixer (on the left) , and got the job done. Would either of these do the job and replace my little DJ mixer in my rack?

Sorry if I sound stupid, but I know NOTHING about sound systems. JT, can you slowly walk me through an easy setup with the following equipment and add a PA mixer or soundboard into the equation so it's simple... Thanks!
 

Attachments

  • PA mixer.jpg
    PA mixer.jpg
    44.3 KB · Views: 1
  • Sound Board.jpg
    Sound Board.jpg
    25.7 KB · Views: 1
Thanks for the video JT...

Here's what I gathered from the video: The musicians on stage have all of their microphones or instruments with a plug that feeds into the box at the end of the snake on stage. That feeds back to the sound board (FOH) where the sound tech sets levels.

On the output of the sound board, the signal goes back to the snake box, where there are cables feeding to the amps. The amps in turn, power the speakers.

If there are four outputs on the box that feed the amps, how do you feed more than four amps?

Will the PA mixer in the left picture do the same thing on a smaller scale? And, with either or both of the devices pictured, would I be able to disregard the crossover in my amp rack?
 
OK - let's go back and ask some very basic questions - and I apologize for going over your head Ty. It was not my intent.

First and foremost -

Tell me all the instruments this band is using. This will help me help you. Depending on the number of inputs needed, the above pictures may indeed get the job done. I have a similar powered mixer for very small events. The CRATE unit is just that - a powered mixer. I'm not exactly sure what the other board is, but it too looks like a powered mixer.

This is where we should start, then JT and I (and possibly Fred too) can advise.
 
Ty
Think of it this way:
Each mic or instrument has it's own input (a snake channel). Some may have more than 1 (ie drums) but we'll ignore sources for the time being. Each channel runs down the snake (which is really a bundle of mic cords in one jacket) to the FOH board. The FOH board has an input for each channel, so you can control the levels (mix) of the group. From the FOH board, you may INSERT effects, such as reverbs and delays. An insert is basically a loop from the board, through the processor and back to the board. The board has several outputs; the main L & R, and several AUX and/or monitor sends. The rows of knobs on each channel strip include usually some EQ features, as well as a few (varies per board) monitor sends. This allows you to make several different monitor mixes for various people on stage. When you look at snakes, these are your returns...ie a 32x4 snake means you have 32 lines running from stage to FOH and 4 running from FOH to stage (ie to amp racks).
 
If there are four outputs on the box that feed the amps, how do you feed more than four amps?

First, if you are running a bi, tri or quad amped system, you probably have a crossover. The crossover has outputs for each; highs, mids, lowmid and subs are what we use. We have 2 4-way crossovers in our amp rack because we run stereo 4 way.

If you have multiple amps within a crossover range, such as we do, you generally will run into one amp, then a signal level out to the next amp. If your amp doesn't have ins and outs you will need to look into a splitter.

Will the PA mixer in the left picture do the same thing on a smaller scale? And, with either or both of the devices pictured, would I be able to disregard the crossover in my amp rack?

The mixer amps you have pictured are basically the same as a mixer and amplifier only on a smaller scale. Mixer amps tend to have less power, less features on the channel strips, lack aux or monitor outs and tend to be less ballsy when it comes to levels. Basically, you probably didn't have enough channels, features and power to do the job they were looking for.

A mixer amp does not replace a crossover in any way.
 
This Thread is very Interesting, great video....always wondered how those snakes worked.....See them at all the concerts.....
 
Tyrone,
What ever you do, Please DO NOT take the crossover out of the equasion.

It absolutly need to be in that rack with the K2's.

If you need a hands on demo, I'll drive up there and show you.

That is some bad ass stuff Bernie sold you,(Think GOOD)

Its really simple, once someone shows you how to correctly.

I have a small Behringer mixer, and it has XLR outputs on it,

I plug my computer into it, then use 2 XLRS from the "master" out, to my 31 band eq, directly to my crossover, which splits the signals, then XLRS to the HI amp, low (mids)amp, and sub amp.

Then speaker cables from the amps to the cabinets.
 
First, if you are running a bi, tri or quad amped system, you probably have a crossover. The crossover has outputs for each; highs, mids, lowmid and subs are what we use. We have 2 4-way crossovers in our amp rack because we run stereo 4 way.

If you have multiple amps within a crossover range, such as we do, you generally will run into one amp, then a signal level out to the next amp. If your amp doesn't have ins and outs you will need to look into a splitter.



The mixer amps you have pictured are basically the same as a mixer and amplifier only on a smaller scale. Mixer amps tend to have less power, less features on the channel strips, lack aux or monitor outs and tend to be less ballsy when it comes to levels. Basically, you probably didn't have enough channels, features and power to do the job they were looking for.

A mixer amp does not replace a crossover in any way.

Valerie,

Are you aware that Tyrone bought Bernie Howards Big JBL rig?

The rack is already pre-wired, and i believe Bernie had it bi-amped.
It has a great EV processer in the rack.
 
Valerie,

Are you aware that Tyrone bought Bernie Howards Big JBL rig?

The rack is already pre-wired, and i believe Bernie had it bi-amped.
It has a great EV processer in the rack.


Yes, I knew that, but it sounds like Tyrone needs a course in the basics; you can't run or troubleshoot without knowing what you've got! Just trying to help explain what folks might be talking about....in laymans terms.
 
I understand the concept...

...of the snake. I can't imagine ever needing a 32 channel snake.

I'm enclosing a picture of the rack (Bernie's) from the back. There are two "inputs" that are 3rd and 4th from the left (I assume left and right channels), and all sorts of outputs to the various speakers. Bernie told me what the four outputs in the middle were, but I forgot (I think they are for the total output of the speakons when using 4 conductor cables and only running one set of cables out... I think).

So let's pretend... Let's say that I have a few guys on stage that use up 8 channels (guitars, keyboards and a drum mic or two, and vocal mics). If I had a mixer (like the left picture above), could I plug them all into that (if it had 8 channels), and feed the output of that mixer into the inputs on the back of my amp rack. Then to the speakers???

Or... same guys and same 8 channels... into the box on a snake on stage, into the sound mixer (FOH), back up to the stage and out of the box (send), then into my amp rack.

Would the only difference be the second choice would require a sound guy working the board?

And, to answer the question... No, I haven't fired up the new system yet, 'cause I'm not sure how.
 

Attachments

  • JBL SR STACK.jpg
    JBL SR STACK.jpg
    131.4 KB · Views: 2
  • Crown K2\'s.jpg
    Crown K2\'s.jpg
    28.2 KB · Views: 73
  • Back of rack.jpg
    Back of rack.jpg
    188.8 KB · Views: 3