Okay, so I cleaned out my gut box and reorganized the cabling in there.
I'll let the pictures speak for themselves, but here's some notes....
One of the pics shows the Front.
I have on top a Furman Power conditioner and Crest 16 X 4 Mixer.
Down the front I have
Furman Power Conditioner
Shure ULXP Wireless (Beta 58 capsule)
AKG wireless
Driverack PA
QSC RMX 1850HD
Crown CE2000
Now for the back.
Along the left side I have a Furman PlugLock. I'm pointing at it. This is one of the single best pieces of gear for taking care of wall warts. I have 3 wall warts as you can see. One for my AKG mic, one for my light board, and a backup for anything that might go wrong.
In the foreground I'm pointing at a non-wallwart plug. This is a black powerstrip for all my other gear on the table. Notice how its screwed in place? No accidents that way.
Now a shot of the back of my Driverack. Notice how cords flow to the left out of the way.
Now a shot of the amp cords wrapped and ziptied to the side of case. Screw type zip ties are genius. I also wrapped them in a figure 8 as much as possible. No coils here.
The plugs in my hand here are for my light board. One for power, one for audio. Pre-ran, just plug and play. When done, the wrap back into the top of the box in the crevice between my furman (on top) and the rack itself.
Speaker cords are cable-cuffed and ride right inside the box. Just uncuff and plug in. When the gig is done, cables go right back into the box.
Power cords are wrapped to the right with a big cable cuff.
I also mounted new locking casters onto my gut box, more about that below.
Now my favorite....
Contico Pro-Tuff Bin available at Lowe's for $50.00
Gorilla Glue - small bottle $6.00
16 - 1/4" bolts about 3.5 inches long with rounded top, washers, nuts $7.00
Locking 3" or bigger casters $11.00 each at home depot. $44.00
Scrap heavy plywood cut to fit the bottom.
Glue wood to bottom of case. Follow directions on glue.
Drill holes for casters.
Run bolts through bottom of case from the inside. Mount casters. Run a washer and nut onto the threads. Dab a little gorilla glue on threads, make it finger tight.
Cut off remaing thread with grinder metal blade or dremmel. Torque down nuts with drill and socket.
I have 3 cases just like this. If you use these specific casters with the blue brake from Home Depot, I can promise you that you can stack these easily and they will not roll. I can't find them cheaper online.
Inside I have 2 moving heads that fit perfectly in this case. I had to dremmel out the top of the case just a hair to make them fit and remove one handle from each light, but its tight and safe. I cover them with the black blankets I use in my setup.
I can get you 16 channel moving heads for around $725 if interested. They are MSD 250's and have really clean optics.
Anyway, so if any of you have thoughts or comments, I'm all ears!
I'll let the pictures speak for themselves, but here's some notes....
One of the pics shows the Front.
I have on top a Furman Power conditioner and Crest 16 X 4 Mixer.
Down the front I have
Furman Power Conditioner
Shure ULXP Wireless (Beta 58 capsule)
AKG wireless
Driverack PA
QSC RMX 1850HD
Crown CE2000
Now for the back.
Along the left side I have a Furman PlugLock. I'm pointing at it. This is one of the single best pieces of gear for taking care of wall warts. I have 3 wall warts as you can see. One for my AKG mic, one for my light board, and a backup for anything that might go wrong.
In the foreground I'm pointing at a non-wallwart plug. This is a black powerstrip for all my other gear on the table. Notice how its screwed in place? No accidents that way.
Now a shot of the back of my Driverack. Notice how cords flow to the left out of the way.
Now a shot of the amp cords wrapped and ziptied to the side of case. Screw type zip ties are genius. I also wrapped them in a figure 8 as much as possible. No coils here.
The plugs in my hand here are for my light board. One for power, one for audio. Pre-ran, just plug and play. When done, the wrap back into the top of the box in the crevice between my furman (on top) and the rack itself.
Speaker cords are cable-cuffed and ride right inside the box. Just uncuff and plug in. When the gig is done, cables go right back into the box.
Power cords are wrapped to the right with a big cable cuff.
I also mounted new locking casters onto my gut box, more about that below.
Now my favorite....
Contico Pro-Tuff Bin available at Lowe's for $50.00
Gorilla Glue - small bottle $6.00
16 - 1/4" bolts about 3.5 inches long with rounded top, washers, nuts $7.00
Locking 3" or bigger casters $11.00 each at home depot. $44.00
Scrap heavy plywood cut to fit the bottom.
Glue wood to bottom of case. Follow directions on glue.
Drill holes for casters.
Run bolts through bottom of case from the inside. Mount casters. Run a washer and nut onto the threads. Dab a little gorilla glue on threads, make it finger tight.
Cut off remaing thread with grinder metal blade or dremmel. Torque down nuts with drill and socket.
I have 3 cases just like this. If you use these specific casters with the blue brake from Home Depot, I can promise you that you can stack these easily and they will not roll. I can't find them cheaper online.
Inside I have 2 moving heads that fit perfectly in this case. I had to dremmel out the top of the case just a hair to make them fit and remove one handle from each light, but its tight and safe. I cover them with the black blankets I use in my setup.
I can get you 16 channel moving heads for around $725 if interested. They are MSD 250's and have really clean optics.
Anyway, so if any of you have thoughts or comments, I'm all ears!
Attachments
-
Gut Box Front View.jpg98.3 KB · Views: 9 -
Rear View Gut Box.jpg109.1 KB · Views: 10 -
Furman PlugLock.jpg154.3 KB · Views: 3 -
DriveRack Rear.jpg115 KB · Views: 1 -
Wires zipped and screwed out of the way.jpg80.9 KB · Views: 0 -
Power Supply and Audio Cord light board.jpg95.9 KB · Views: 3 -
16 Channel Moving Heads.jpg100.9 KB · Views: 3 -
3 inch Casters with Locks.jpg94 KB · Views: 2 -
Contico Protuff With Casters.jpg108.9 KB · Views: 1 -
Rear View Gut Box with Wires.jpg120.1 KB · Views: 3