Mic Volume

To many ads? Support ODJT and see no ads!

oldschooldj

Mac Daddy DJ
Jul 7, 2012
709
843
65
FT. CAMPBELL
Been fighting low volume in my mic channel I will give you set up then more information:

EV-R300HD wireless hand held (x2) or Yamaha wired mic (x2)
Into Numark Mix Deck Express (x2)
Into V-DCONE processor (nothing done to surpress mic or feedbacK) (x3)
Into EV- CP4000 amp (x2) or EV-Q1212 amp (x3)
Into many different EV speakers TX1122, TX1152, TX1181, ZX1

The Mix Deck Express says it has balanced inputs (checking on line specs, but you can't get Numark to answer the phone), I have to drive the slider on channel 2 and the gain structure to the max to get good volume out of the mic, it is clear, no hum and has good voice quality, it is just not loud.

I am coming out of the back of the EVR300HD on the 1/4 jack, I have selected line level and the gain nob is all the way up. To let you know now I have two of everything I have mentioned and have tried different combinations with same results.

I use a balanced mic cable of 25ft or less. I did find out today that my EV wireless in an unbalanced output on the 1/4, but my yamaha hand helds are balanced XLR to 1/4 cables and the handhelds have the same issue. Otherwise I would have already tried the XLR out on the back of the EV to the 1/4 input on the Numark, might that sound better?

Is the problem the cheap Numark Mixers just have poor mic inputs?
Is going from unbalanced out of the EV wireless to balanced cable, to balanced Mix Deck input loosing some gain?

I am thinking of buying a feed back destroyer with a mic gain in the system, could that help?

Steve already helped me some, but I can't figure out if I am doing something wrong with cableing.

Thanks Ray J.
 
Been fighting low volume in my mic channel I will give you set up then more information:

EV-R300HD wireless hand held (x2) or Yamaha wired mic (x2)
Into Numark Mix Deck Express (x2)
Into V-DCONE processor (nothing done to surpress mic or feedbacK) (x3)
Into EV- CP4000 amp (x2) or EV-Q1212 amp (x3)
Into many different EV speakers TX1122, TX1152, TX1181, ZX1

The Mix Deck Express says it has balanced inputs (checking on line specs, but you can't get Numark to answer the phone), I have to drive the slider on channel 2 and the gain structure to the max to get good volume out of the mic, it is clear, no hum and has good voice quality, it is just not loud.

I am coming out of the back of the EVR300HD on the 1/4 jack, I have selected line level and the gain nob is all the way up. To let you know now I have two of everything I have mentioned and have tried different combinations with same results.

I use a balanced mic cable of 25ft or less. I did find out today that my EV wireless in an unbalanced output on the 1/4, but my yamaha hand helds are balanced XLR to 1/4 cables and the handhelds have the same issue. Otherwise I would have already tried the XLR out on the back of the EV to the 1/4 input on the Numark, might that sound better?

Is the problem the cheap Numark Mixers just have poor mic inputs?
Is going from unbalanced out of the EV wireless to balanced cable, to balanced Mix Deck input loosing some gain?

I am thinking of buying a feed back destroyer with a mic gain in the system, could that help?

Steve already helped me some, but I can't figure out if I am doing something wrong with cableing.

Thanks Ray J.
Ray, for any serious use of a Mic to make important Announcements at important Events, I would use nothing less than a Live Mic Mixer, no matter if it is a small one. I have a Headphone/Mic Combo that makes for hands free operation and that is the only one which is plugged into my DJ Mixer. The DJ Mixer's Main Outputs then go into the LIve Mixer's Inputs where it can be adequately tailored and brought to true line levels.
Having said that, I would use the balanced outputs of the Mic instead of the unbalanced outputs. If you are going from Balanced XLR to 1/4" and you want to remain balanced then you have to use a TRS 1/4". That connector also has to be TRS acceptable.
 
  • Like
Reactions: oldschooldj
Have you tried coming out of the wireless receiver to the mixer using a balanced XLR to TRS (1/4" 3 pole) cable? Some circuits that receive balanced signals may react differently to an unbalanced one. Maybe that will get you some additional gain room. Otherwise as we spoke, you can put a small mixer into the mic 1 or 2 inputs and balance the mics and adjust the gain (so you can use the mixer capabilities of talk-over and such) .. or you can feed the output of the DJ mixer into a small live sound mixer and merge in the other mic(s) there. Many options.
 
  • Like
Reactions: oldschooldj
I had the opposite problem, couldn't keep the volume down until I found out there's a switch inside the wireless handheld that attenuates the signal.

I have a mackie DFX-6 that does what you're talking about with a wired mic. I have to turn the trim almost all the way up, but it's loud enough.
 
My first thought was not the mic, the mixer, or the speakers...but the Processor.
I know you said it has nothing for mic suppression...
but have you tried bypassing it to be sure? (pun not intended)
And if you have a powered speaker handy, trying plugging the mics directly into the speaker,
just to make sure it's not the mics.
 
  • Like
Reactions: oldschooldj
Thanks Mike! It is definetly the inputs on the mixers. I bought Numark mixers (Mix Deck Express) as I liked the features of (all in one package):

Computer Input
USB inout
CD/MP3
Two mic inputs with one on a vertical slider

I also fell short in my research and went with a product I had great luck with in the 1980's,and found out 30 years is a long time for a company. I had Numark turntables and mixers in the 1980's and had great luck, warranty and phone support. Fast forward 30 years and Numark stuff is not that great and all the old guys who had customer relation skills have left Numark, heck I guess all the guys who even know how to pick up the phone left Numark :)

I bought cheap mixers from a average company and they are the problem. The mic gain in these mixers is junk. I will band aid them for a year or so, with a Beringer Shark or something along that line that will increase the gain and help with feedback. I will then go out and buy quality mixers/controllers, maybe Pioneer or Denon, I will come in here and ask you experts.

Ray J.

I get more help on my Numark stuff from the VDJ forum than from Numark.
 
  • Like
Reactions: Ausumm
I won't use Numark mixers as my main mixer anymore because they all seem to have a chronic mic input problem. I believe my tech guy said they all have bad input capacitors (I think that's what he said).
 
BTW Ray, have you tried using an Inline Impedance Attenuator?
 
Had the classic Numark mixer as my very first.
Got is used and beat the crap out of it for years...and it still works. (although I have retired it)
I guess it's true that they don't make things like they used to.
Glad you discovered the culprit!
 
BTW Ray, have you tried using an Inline Impedance Attenuator?
Attenuators will reduce the level more - say for a hot signal. He needs amplification.