Need a big ole volume knob

To many ads? Support ODJT and see no ads!

rickryan.com

Mac Daddy DJ
ODJT Supporter
Dec 9, 2009
20,055
18,457
62
Hendersonville, TN
www.rickryan.com
You guys may remember the GTD mics I put in at an auditorium at my day job (perhaps not). Yesterday, I got a call from the facility manager, asking my assistance.

The system they have is a yammy mixer (12-channel), and 300-watt "industrial Peavey" power amp (has hard-wired connections instead of plugs. It has a single, EV speaker hanging at the ceiling (15-feet), about 12 feet in front of the stage area. My guess is they probably got hit with lightning, which possibly damaged the amp and sounded like a driver was fried. The interesting bit about the system is they have a potentiometer hard-wired between the amp and the speaker with the knob located at the back of the room.

Fast forward, I brought in a pair of Carvin 2-ways (15") and an IPR3000. Stripped out the old amp, put in the new, ran speaker cables to either side of the room and have the cabs sitting in chairs (40-foot spread) as a temporary measure. We're probably going over to Guitar Center later to pickup a new amp, driverack and I'm thinking some yammy 15s, along with wall mounts for the speakers. My intention is to mount the speakers about 9 feet up, opposite side, and against the wall, even with the stage area. The sound today is very good. Tons of headroom, the mics are loud and clear and the only way you can get feedback is to walk right up in front of a speaker. BTW, this is probably a 50X100 foot room.

They normally keep the sound system cabinet (wall unit) locked and the inputs hot. You just walk in, either plug in a wired mic or put batteries in a wireless and it just works. Simple, simple. They do NOT want anybody messing with settings on the mixer. What they do want is that overall volume knob. I'm thinking to have some kind of passive, single-knob "mixer" that I'd put between the yammy mixer and the driverack/amp. We'd probably just drill a hole into the steel cabinet, mount the knob and let it be a simple volume override. Hopefully, it won't even need to be touched, especially with all the extra headroom they now have. Sorry to be so long but does anybody have a recommendation for this?

BTW, we have 8 wireless mic capacity with the 2 GTD units. I'm using the summed output on each unit to send to 2 channels on the yamaha mixer. We're probably going to add a 2-channel GTD that will have bodypacks/lavs. They'll have 8 hand-held wireless, 2 lavs, 4 hard-wired plugs, and a laptop input (1/8"). Should be a cooking little rig and easy enough for anyone to operate.
 
  • Like
Reactions: 1 person
If money isn't an object, a dbx DriveRack 260 (or the similar install version 220i) would be great, as it has the ability to accept zone controls for remote volume/muting/etc.

Alternatively, a pair of powered speakers with remote volume control might work (QSC K/KW series have them).

I would never put anything between the amp and the speaker (for any power above a few watts) .. it should go before the amp.
 
Last edited:
You guys may remember the GTD mics I put in at an auditorium at my day job (perhaps not). Yesterday, I got a call from the facility manager, asking my assistance.

The system they have is a yammy mixer (12-channel), and 300-watt "industrial Peavey" power amp (has hard-wired connections instead of plugs. It has a single, EV speaker hanging at the ceiling (15-feet), about 12 feet in front of the stage area. My guess is they probably got hit with lightning, which possibly damaged the amp and sounded like a driver was fried. The interesting bit about the system is they have a potentiometer hard-wired between the amp and the speaker with the knob located at the back of the room.

Fast forward, I brought in a pair of Carvin 2-ways (15") and an IPR3000. Stripped out the old amp, put in the new, ran speaker cables to either side of the room and have the cabs sitting in chairs (40-foot spread) as a temporary measure. We're probably going over to Guitar Center later to pickup a new amp, driverack and I'm thinking some yammy 15s, along with wall mounts for the speakers. My intention is to mount the speakers about 9 feet up, opposite side, and against the wall, even with the stage area. The sound today is very good. Tons of headroom, the mics are loud and clear and the only way you can get feedback is to walk right up in front of a speaker. BTW, this is probably a 50X100 foot room.

They normally keep the sound system cabinet (wall unit) locked and the inputs hot. You just walk in, either plug in a wired mic or put batteries in a wireless and it just works. Simple, simple. They do NOT want anybody messing with settings on the mixer. What they do want is that overall volume knob. I'm thinking to have some kind of passive, single-knob "mixer" that I'd put between the yammy mixer and the driverack/amp. We'd probably just drill a hole into the steel cabinet, mount the knob and let it be a simple volume override. Hopefully, it won't even need to be touched, especially with all the extra headroom they now have. Sorry to be so long but does anybody have a recommendation for this?

BTW, we have 8 wireless mic capacity with the 2 GTD units. I'm using the summed output on each unit to send to 2 channels on the yamaha mixer. We're probably going to add a 2-channel GTD that will have bodypacks/lavs. They'll have 8 hand-held wireless, 2 lavs, 4 hard-wired plugs, and a laptop input (1/8"). Should be a cooking little rig and easy enough for anyone to operate.
Seems to me you already have it figured out so what I say may not matter but that is not the way I would set it up. Why not utilize the full capabilities of the Mixer and give each Mic its own Channel so that if several people are using the Mics you can adjust each person's volume. some people speak loud some people speak soft and hold the Mics too low. I would also mount the speakers higher so they project farther and also reduce the likelihood of feedback even more. Number the Channels for each mic and put corresponding Markers on the Mics.
 
I agree on the pot in the current setup. Kinda freaked me out to see they'd run all that cable between the amp and speaker and put a pot in line with it.

Money isn't really an issue. I think he said he's got $5k. The stuff I layed out (speakers, amp, driverack) will come in well under $2k. I don't want to use active speakers as we'd have to run circuits to the hang points. Incidentally, they use a circuit breaker to turn power off to the wall socket that powers the sound system (shudder) and I found out I'm the first guy who has been allowed in the cabinet in the 8 years since it was installed. On the new setup, I'm installing a rack-mount power unit with conditioner/surge in it and it'd be nice to be able to drop a remote on/off switch to the edge of the cabinet. Forget that flipping the breaker bit. I'm leaning toward a pair of yammy passive speakers. I just like the tone on those dudes. The facility guy said he was waiting for the go ahead and we may head over to GC this afternoon or tomorrow. Incidentally, I believe it's a single EV EVI-15 that's hanging at the ceiling now. BTW, do ya'll know of any rack-mount power units (multi-strip) that does staged power on/off? It'd be nice to avoid that "pop".
 
Last edited:
A Behringer Ultrazone ZMX8210 will also do the job for remote control without drilling into anything.
 
A Behringer Ultrazone ZMX8210 will also do the job for remote control without drilling into anything.

Nah, won't work. They want to keep that cabinet LOCKED, period. They don't want anyone (other than me and the facility guy) to be able to even reach the mixer. The only thing I can think of is a single knob that is accessible from the outside of the cabinet.
 
I agree on the pot in the current setup. Kinda freaked me out to see they'd run all that cable between the amp and speaker and put a pot in line with it.

Money isn't really an issue. I think he said he's got $5k. The stuff I layed out (speakers, amp, driverack) will come in well under $2k. I don't want to use active speakers as we'd have to run circuits to the hang points. Incidentally, they use a circuit breaker to turn power off to the wall socket that powers the sound system (shudder) and I found out I'm the first guy who has been allowed in the cabinet in the 8 years since it was installed. On the new setup, I'm installing a rack-mount power unit with conditioner/surge in it and it'd be nice to be able to drop a remote on/off switch to the edge of the cabinet. Forget that flipping the breaker bit. I'm leaning toward a pair of yammy passive speakers. I just like the tone on those dudes. The facility guy said he was waiting for the go ahead and we may head over to GC this afternoon or tomorrow. Incidentally, I believe it's a single EV EVI-15 that's hanging at the ceiling now. BTW, do ya'll know of any rack-mount power units (multi-strip) that does staged power on/off? It'd be nice to avoid that "pop".

This Furman will: http://www.furmansound.com/product.php?id=PS-8R as will most of the Monster Power Pro units.

- - - Updated - - -

Nah, won't work. They want to keep that cabinet LOCKED, period. They don't want anyone (other than me and the facility guy) to be able to even reach the mixer. The only thing I can think of is a single knob that is accessible from the outside of the cabinet.

No .. the Behringer (or dbx) would go in the cabinet and a remote volume would go outside. That Behringer has a euroblock to attach left and right volume controls to. The dbx has what looks like an ethernet port that remotes attach to.
 
Last edited:
  • Like
Reactions: 1 person
No .. the Behringer (or dbx) would go in the cabinet and a remote volume would go outside. That Behringer has a euroblock to attach left and right volume controls to.

Cool beans. Are you saying the driverack can be setup with a single, external volume knob on it?

- - - Updated - - -

You know, I have to say I'm a bit disappointed. Bob hasn't chimed in to say "You have no business doing that" nor has Canute chimed in to say "You need to hire an expert". ;)
 
I agree on the pot in the current setup. Kinda freaked me out to see they'd run all that cable between the amp and speaker and put a pot in line with it.

Money isn't really an issue. I think he said he's got $5k. The stuff I layed out (speakers, amp, driverack) will come in well under $2k. I don't want to use active speakers as we'd have to run circuits to the hang points. Incidentally, they use a circuit breaker to turn power off to the wall socket that powers the sound system (shudder) and I found out I'm the first guy who has been allowed in the cabinet in the 8 years since it was installed. On the new setup, I'm installing a rack-mount power unit with conditioner/surge in it and it'd be nice to be able to drop a remote on/off switch to the edge of the cabinet. Forget that flipping the breaker bit. I'm leaning toward a pair of yammy passive speakers. I just like the tone on those dudes. The facility guy said he was waiting for the go ahead and we may head over to GC this afternoon or tomorrow. Incidentally, I believe it's a single EV EVI-15 that's hanging at the ceiling now. BTW, do ya'll know of any rack-mount power units (multi-strip) that does staged power on/off? It'd be nice to avoid that "pop".You will need to buy a Power Conditioner/ Sequencer . The Pop occurs because Gains are up on the Channels and signals are "hot"!
Unless you are a Qualified Rigger and Electrician, I would hope you seek competent assistance before attempting to install devices in a commercial arena. That is, if you are willing to share the Limelight and Credit for the final work.
 
Last edited:
Unless you are a Qualified Rigger and Electrician, I would hope you seek competent assistance before attempting to install devices in a commercial arena. That is, if you are willing to share the Limelight and Credit for the final work.

Cue Krusty. :laugh:

Dude, hiring an outside "expert" is what got that screwed-up system installation to begin with. Thanks for not disappointing, however.
 
I don't believe you need either if you are neither rigging or installing circuitry. There could be a need for a low-voltage certification if wiring is run through walls/plenums, but generally "hooking" things up doesn't fall under that category .. or we're all guilty.
 
  • Like
Reactions: 1 person
Picked up the gear today. Crown c3000 amp, jBL Prx cabs ($487 each) and dbx drive rack. We're adding a 2 channel gtd wireless lab and already have 2 x 4 channel gtds. The facility guy is beyond thrilled.

Sent from my DROID BIONIC using Tapatalk 4 Beta

Which DriveRack did you end up with?