Noob Question About Power Distro.

To many ads? Support ODJT and see no ads!

cbarronx23

New DJ
Dec 12, 2006
1,093
0
35
So by the end of summer, I hope to have completed my full-sized rig. One thing that has me EXTREMELY worried is power. I have no expierience whatsoever in how I would plug into a breaker, or even distribute the power properly. Ia assuming I would need 2 30 amp circuts to safely handle sound and 1 for lighting.

Would I need something like this? How would I connect something like this to the building's power?

Any help would be greatly appreciated.

Thanks,
Chris B.
 
Greets, Chris.

These distros are very nice for managing larger electrical loads. There are two methods of connecting a distro to AC power.

The easiest method is via an electric range plug. That's OK if there's an outlet in the venue that you can get to and are permitted to use.

The second and most popular method ~ tie in to the mains in a service panel. This method requires removing the panel cover and clipping cable ends to the busbars.

Hope this helps. :)
 
So you're saying all I'd need to do is to plug the distro into an outlet?

Or if there is no outlet it would need to be connected to the service panel?


2 questions. What would one of these outlets look like?

also, what kind of wire would I need to connect to the service panel?
 
Oh Nooo!!!

Do not mess around with electrical current if you don't know what you're doing... you will KILL yourself.

I just build a distro panel and it is plugged into a 220 volt outlet. That's the only purpose for a distro is to step down 220 into usable 110 for your lights and equipment. By asking the questions you just did, it's clear you don't know what you're doing... DON'T DO IT!

Go to a licensed electrician and ask him/her to build you a portable one with at lease a 25 foot lead so you have some distance to work with. You will probably only need 4 or less circuits (each with a breaker). I bought all of the parts for about $100 to build mine, but figure on paying $300 or more to have an electrician build you one.

Also, the venue MUST be equipped with a range socket near the dance floor in order for you to even be able to use one. Most hotels have them, but very few VFW's and legions have them.
 
Go over to prosoundweb and search for "distro". You will come up with a few hours of educational reading. Just read. Don't bother to ask newby electrical questions over there because you will only get flamed for asking.
 
See the thing is we cater mostly to schools. Most of our gigs are either in school gyms (high school and middle school) or in large hotel ballrooms. I guess the hotels would have the sockets, but the gyms probably not. I've got an uncle who's an electrician, I'll try to ask him next time I see him.
 
note, tying into the busbar may be against a) fire code and b) electrical code

Luckily my boss taught me a little about 3 phase power, 208V, serious voltage! Find a qualified electrician, i have a friend my age who is one, so if I have a question, I can ask him. Ask around, but be sure you ask the right people.
 
Checking with an electrician is a good idea. There are commercial rack mount distros available, Furman and Motion Labs make them, among others. But you need to know what kind of power may be available, single or 3 phase, and what type receptacles. I use both single and 3 phase distros, and have a variety of plugs for different venues.

Also be aware that many hotels now charge a stiff fee for plugging in to anything more than a standard wall outlet. I have a clause in my contract that covers power requirements and make sure that the client knows that arrangements must be made with the venue, and that they are responsible for any additional expense.
 
See the thing is we cater mostly to schools. Most of our gigs are either in school gyms (high school and middle school) or in large hotel ballrooms. I guess the hotels would have the sockets, but the gyms probably not. I've got an uncle who's an electrician, I'll try to ask him next time I see him.

cbarron - Answer a couple of questions that have not been asked as of yet in this thread. As Tyrone said, you are messing with serious amounts of voltage here that has the ability to end your life since you obviously have not had prior experience with what has so far been described.

Give us a rundown on what you plan on using for these kinds of events? If you could put together a list of whats in your rig, that would help us figure out just exactly how much power you are really going to be pulling.

As a side note, I had an electrician build a distro panel for my business. There are pics in the photo gallery. You can get an idea of what a custom distro looks like.
 
If your thinking of having a rig that is going to require a distro, your not exactly a mobile DJ service. The additional work for the distro, equipment, hanging of the lights and teardown may be more than you wish to bear.

I have worked with many events that are large scale including fighting rigs (www.xfcfights.com) Live sound lighting and video for big names such as zz top, papa roach, saliva. It takes a large crew and even some IATSE stage hands to help with the setup, typically 8 hours with enough help.

For my smaller rigs I use a Co-Pilot on one circuit (use an extention cable) and another going to a separate ciruit. Doing so should give you plenty of power. Don't overestimate your power requirements.
 
I understand what he is thinking, doing a lot of school dances in my time it is not the easiest thing in the world sometimes to find 4 circuits in most gyms.... I had a light guy for awhile who knew about all dat stuff and we would hook into the panel with a Distro unit,,, we never told the school ahead of time because they always said no...

When he left I didn't feel safe doing it myself and that is when I invested in a bunch of 100 and 50 foot 12/3 and some 10/3 power cords....

I would run into the coaches office, laundry room, down the hall into the bathroom if I needed...

At one point I needed 6 circuits to run my show... THAT's hard to find.

One thing about 220v plugs,,, there are a number of configs, or at least there used to be, so you might have to carry a few in case you have to change for each venue..

If you are doing the same venues, after awhile, you know what and where.

Depending on where the panel or plug is, you might need or want a LONG cable from them to your box... my buddy had a 100 foot cable,,, big thick ass thing that was a pain,,, but it did make powering up the show easier....
 
when you start dealing with serious current and voltage, even as low as 110 volts be sure to have high gauge wires... You do not want to create a fire hazard just because your pulling too much current that melts your wires, and causes a short.
 
Sorry, guys... I should have been more clear. I tend to presume at times.

I've been doing industrial electrical installs so long that I tend to forget that not everyone understands the hazards involved. Industrial is usually 480 volts, 3-phase. Some older services were 575 volts.

I'll try to make it right here. :)

Only an experienced electrician should go into a service panel, period. Even I don't care for working in a panel when it's hot. Some makes of industrial/commercial panels have breakers that are mounted to the busbars with screws. I stand on a rubber mat and wear lineman's gloves for hot work. Work with one hand... the other hand is behind your back. And never work on a hot panel alone.

Typically, distros are 4-wire systems. Two hot conductors (240 or 208 volts, depending upon the service), a neutral and a ground. Voltage between either hot and neutral is 120 volts. If you don't know which busbars are which (and don't have a voltmeter), do not attempt to clip up.

Often there is no short-circuit protection feeding those busbars. If you accidentally short between 'em with a clip, the resulting explosion will be like a hand grenade going off in your face.

I know... I've done it. :eek:

If you don't know exactly what you're doing, don't attempt it. It isn't worth the risk.

That being said, Chuck is right on. There may not be a 4-wire range outlet anywhere near where you have to set up. There may not be one in the house at all. Heck, at most of the venues we've worked, we were lucky to have the one 15 amp outlet we had. So... we pretty much designed our system to function on a single AC circuit.

Hope this helps.
 
Right now, we have a pair of EONs, a pair of JRX subs, mixer, DRPA, Plus Projector, two computers (sometimes 3-4), single DVD units, Chauvet DMX Controller, 2 Martin Mania SCX-500's, 1 Martin EFX-500, and two AMDJ MegaStrobes. So far I've never had a problem running on a single AC circut.

However, business has been fairly good and I have been saving up for a while, and I am getting ready to add a lot to my rig. Something like 4 Crown XTi 4000 (or similar), 1 more projector, 2 more scanners, 1 more EFX, some LED pars, and maybe some techno strobes. I've got around 4-5K set aside for now, and by summer hopefully another 1k.

My first concern, naturally, is having enough power for all of this. I would probably need 2 circuts for sound alone, 1 for lights, and another for my rack and projector.

As I said before, I do have an uncle who happens to be an electrician. When I see him again in about 2 months, I'll mention it to him and see what he says.

But, if anyone could just tell me what I would need, such as wiring, etc. I would really appreciate it. Right now I think I understand what I would need as far as the distro panel (portable service panel, with AC plugs). I just need to know what I would use to connect this distro panel to the building's power. I just need to know what I'm talking about when I speak to an electrician, so I don't look like a complete idiot.

Thanks,
Chris
 
I prefer rack mounted distros myself. The ones from Motion Labs use Square D breakers and are A-1 ~ they even offer power cables and different plug configurations. They ain't cheap, however. I'm not familiar with the Furmans.

Chris, have a chat with your uncle before placing an order. He'll be able to recommend the solution that's best for your needs. :)
 
Fred, is this what you're talking about?

http://www.motionlabs.com/download/1300-000-06-1-02.pdf

And how expensive would these be?
Actually this particular configuration with the 4-wire NEMA outlets would be overkill for your purposes. This one is touring grade. I believe Motion Labs offers models with standard 20 amp, 120 volt 3-wire receptacles and circuit breakers for each.

I haven't browsed the website in a couple of years and forget which model it is. :( If I'm not mistaken, they're priced out at the website.

Anyhoo, if you need a quality, rackmount distro, Motion Labs does offer a quality product.
 
Chris,
That motion labs distro you showed us, and as wolfie stated is absolute OVERKILL for the stuff you want to add.

It would also involve twistlock cableing, as well as some large twist locks,
which add to the cost.

The band i work for use equipment like this, But we use it to run (4) QSC pl 9.0's and a bunch of camco's that are like 6000 watts apiece.

I believe if you had a portable distro that will run off a 220 wall plug, a couple of different ends for it, and say (2) sets off 100 foot cables, you would be fine.

You can find used touring grade, Big boy stuff here;

www.gearsource.com

Also, if your going to risk tapping the distro yourself, you had better UP your INSURANCE coverage.
Otherwise, hire an electrician.
 
And remember to always check with a volt meter the voltage on the outlets in your distro to be sure you're not getting 220 V. You can never forget a mistake in wiring.