OK I bought the sub... now help me with use

To many ads? Support ODJT and see no ads!

MADNESS

Well-Known DJ
Dec 20, 2006
2,293
49
65
Florence, AZ
www.primetimedj.net
First I want to thanks everyone for all of the input on the Subwoofer thread. :sqlaugh:

Alright, I bought my first sub, will be here next week. I bought the b52 act 18 XS. I will be running them with mackie 450's. I have never ran a sub prior to this and want some help with the setting and use of heavy bass.

This I do know. I run from the mixer to the sub on both channels then to the Mackies but am curious about the fine tuning of the sepakers for quality sound
My questions is how do you know what level to set the sub at to ensure you are not getting to much thump?
And My mixer is a denon DNX500, should I run it with the EQ on or off and how should I run the bass on the mixer?

Also any other hints you can throw my way would be great!!
 
Just wanted to congratulate you on your purchase...

As far as being technical? well, I don't know how much THUMP you want / need.... but I would let my ears be my guide.

Did you ever go into a Best Buy when the have all their subs thumping at once? It is actually painful. Ya don't want that! :sqerr: :sqwink: :sqlaugh:
 
Scott
Im not familiar with the controls on the 52 so unsure which would give sound adjustment versus volume. Use your ears and adjust the EQ or adjustment available on Sub if you run a EQ it will enhance your tops as well unless you run seperate outputs to the sub with a EQ solely for said Sub. Good luck!
 
Thats actually one of the reasons I use an active crossover. You have much more control of what your amps actually focus on, and can change gain on the fly to increase/decrease "thump"

Yes - It will cost you $90-$250 ($500 if you go high tech DriveRackPA) and it introduces yet another single point of failure.... but so does your EQ and mixer...
 
Hey Mad! There will be nothing to adjust but your sound level. You are running all powered gear and the speakers are already tuned. Just dont drive the Mackies in full stereo. I don't know the speaker but their should be some kind of a bypass for just mid/high only. As for the sub, start off at 9o clock and take the mixer up 1/2 way and adjust the gains to fit the room. As for the Mackies I would just keep those at 12o clock the whole night. The sub will take away a lot of pain for the mackies. They won't go thermal. Buy adding this sub, you just extended the life of your Mackies.
Good luck and enjoy you new purchase.
 
Thats actually one of the reasons I use an active crossover. You have much more control of what your amps actually focus on, and can change gain on the fly to increase/decrease "thump"

Yes - It will cost you $90-$250 ($500 if you go high tech DriveRackPA) and it introduces yet another single point of failure.... but so does your EQ and mixer...

Pete do you use a crossover for powered gear of passive? I only use it for 2 amps or more when running subs.
 
My quick thought...

I am by NO means very technical about sound... and I thought I'd toss this in since I havent seen it so far. Don't run "full range" to your top speakers when running a sub. You'll have better sound if the tops don't have any bass sent to them.
 
A DBX 234XL, will take care of things.
 
Pete do you use a crossover for powered gear of passive? I only use it for 2 amps or more when running subs.

Both. There really is no difference between active and passive gear except where the amp sits...

Yes - Most active subs have passive high-pass crossovers for the tops - but again - it's passive, and most of the time un-controllable. Hopefully you and the manufacturer have the same idea on optimal high-pass frequency.... and even so - do they even know what tops you've got there?

Yup - some active subs let you dial in the frequency... but few allow gain. And finally - these controls are FAR away from you with the subs and tops....

The crossover - now thats right there in your rack. You can control crossover freqs, gains, and on some of the better units delay...

Maybe I just can't make up my mind... but I like to be in control!
 
A DBX 234XL, will take care of things.

I've used Crossovers from Rane, DOD, Dbx and Behringer... Rane and Dbx seemed to offer best control, but also made you think about your sound. My sound sound system now isn't exactly great, but I'm living with a DOD SR835II which is balanced...

When I can talk myself to replace the sub and tops - DriveRackPA or the Rane will be in my rack.
 
Another nice aspect of active crossovers ~ set and forget. :)

Once you get your tone balanced out to your liking with a bi- or tri-amped system, the crossover points may be left alone.

To be sure, you may use the crossover to boost or cut a bit depending upon the house acoustics. But the crossover points don't change.
 
I used to run Mackie 450s and an ACT-18 sub. What I did was run from my mixer to the sub, then run out of the Full Range XLRs to my Mackies. The crossover in the ACT-18 is set a little too high, so push in the Low Cut button on the Mackies. This will give you a fuller sound on your tops without pushing them to reproduce low bass.

I almost always run the gain on my ACT-18 at 1:00. You can run the gains on the Mackies at 12:00.