Chauvet Intimidator Scan LED 200 vs 300

To many ads? Support ODJT and see no ads!

rickryan.com

Mac Daddy DJ
ODJT Supporter
Dec 9, 2009
20,055
18,457
62
Hendersonville, TN
www.rickryan.com
I'm comparing these two units. The most notable differences I see are:

200: 18w led
300: 60w led

200: 9000 lux
300: 9650 lux

200: 7lbs
300: 14lbs

The specs don't seem to add up. An 18w element makes 93% of the amount of brightness as the larger/newer unit? Anybody had any real-world experience with these?
 
FYI...the 200 has a 15* beam angle vs the 300's 21* beam angle

The more narrow beam will concentrate more light than the wider beam...completely different applications of light.

The 300 is substantially brighter, and actually the better choice for club installations, etc.
 
I know i love those 300's and am hoping to pick up 4 in the near future. I was actually about to get them last month but decided to pick up my intimidator spot 250's first. So the Intimidator 300 scanners will have to wait a little while, but i will own them :)

I'm close to pulling the trigger. My local GC rep sorely tempted me with $450/each on a pair.
 
About an hour ago I returned from a Chauvet Show right down the street from me. They had a 15% discount on all Chauvet products plus some closeout specials. Some lights impressed me and some did not.
 
I went by GC at lunch today and tried out the 300s. Wow! Those things kick out a lot of light and have a nice, big and bright gobo. Hope they've got a pair in stock as I'm planning to go back tomorrow with CC in hand. Have a school function Sat 9a-3p, then a wedding that evening then a school dance on Tuesday. Should be able to give them a nice workout. Kinda looking forward to ditching "the colored dots" for a bit.
 
One immediate observation; This unit has either too-fast or too-slow on the automatic programs. I haven't found one that's in the middle yet and am hoping that sound-active will work. Not sure what it'll have on DMX and I'd hate to think about having to program a bunch of scenes to make these use-able. I pulled it out at home and turned out the lights in the living room. VERY bright. A single fixture was plenty to light up our entire living room. Our kids went nuts. I'll be able to use them 3 times over the next week so should have a good feel for how well they'll work.
 
Follow up: I used the Chauvet Intimidator Scan LED 300s (2 of them) at two events on Saturday. Had a kid's karaoke event at my wife's school. The room is a 15X35 and was darkened. Set the units on slow scan, random gobos and they did fantastic. Later that evening, I used it at an outside wedding in a 30X60 tent. Put both units on a t-bar, synced together with L-R pan (opposite from each other), no DMX control.

CONS: The unit's automatic program seems to be either too slow or too fast. No in between. Sound active was better at a low volume but at the wedding gig sound active was much too fast. I ended up having to flip between the modes manually. The scans seemed to spend an awful lot of time around the very edges of the coverage pattern. I'd put it at maybe 70% on the edges and 30% towards the middle/front (where the fixtures are aimed).

PROS: VERY bright. Much brighter than I expected. In fact, it was probably too bright in the classroom setting. At the wedding the faster scan created a lot of energy on the dance floor and filled the entire tent. My normal rig is; 1 Colorstrip, 1 Vue3, 1 Vue6, 1 Triphase, 1 Revo4. I'm probably going to pull everything off and just use the colorstrip, vue6, Triphase and the 2 scanners. The patterns were bigger than I expected and against a tent ceiling they looked fantastic.

SUMMARY: Overall impression was that it was a definite step up from what I've been delivering. The Revo4 and Vue3 were useless next to these fixtures. My initial reaction is that 2 should be enough to do most weddings but 4, if stationed in opposing sides of the room would be even better. Highly recommended. Here are a few shots from the wedding job:

IMG_1523.jpg

IMG_1541.jpg

IMG_1547.jpg

IMG_1552.jpg
 
so I guess you wont be trying to return them to GC eh? YOu going to buck up and get the DMX software to allow you more control per your con commentS?
 
Hi,

Glad to hear some talk about these 300s, I got a pair in the spring and love them but have the same complaint about auto modes being too fast or too slow, with sound active seeming quite a bit too sensitive for my gigs. The manual is far lower quality than the lights unfortunately (mine has several typos) which leads me to a question/comment for Rickryan... The manual references a hidden menu on the control panel, which I can access no problem by following the directions. The manual also mentions adjusting sound sensitivity in the hidden menu and refers to 'more information below' or something to that effect. However, the list of menu parameters doesn't mention sensitivity. There is a 'L' parameter in the menu (not the table) which I infer could be this sensitivity adjustment. I couldn't tell if there was any result from changing it though... Any thoughts? I haven't contacted tech support yet (have favored using a DMX controller with speed adjusted on the controller to roughly match the tempo of the music, which also enables dimming the output until the brightness of which they're capable becomes appropriate) but that could be the next step.

I would like to mention that my favorite use of these lights involves a mirror ball. I use a lights tripod stand / t-bar with the scanners at each end of the bar and a cross bar pointing forward hanging a mirror ball centered between the lights. When the lights are in slow mode and they lazily scan across the mirrorball, it's brighter than any other mirror ball I've ever seen, and a nice visual treat for the crowd. DMX programming can be used to trigger the effect on demand as long as your lights/stand/ball are consistently positioned relative to each other. Add fog or haze for maximum impact, venue permitting.

I'd be happy to engage in further discussion, I've had a real hard time finding much (any?) real-world-experience-based talk about these lights. (esp. the microphone issue and the possibility of gobos being changed)

Take care, enjoy your new toys... err, tools! :)
-Lane
 
Another afterthought: I have noticed the same thing about the lights pointing off to the side a little more than makes sense to me. I wonder out loud if setting the pan home positions 30 degrees-ish inward for each light (assuming you're using them parallel to each other and more or less behind your table) might make them spend more time in the middle?
 
the 200's performed amazingly well, they where on par if not brighter then the halogen scanners we had in there before. 4 200's replaced 4 ADJ deluxe scan 250's and 2 martin t-rex's. Needless to say it made our halloween party tits, cuz the 200's where bright crisp and clear.