Kevin's Tip of the Week March 26

To many ads? Support ODJT and see no ads!

Kevin Nichols

DJ Extraordinaire
Jul 20, 2006
2,012
90
56
Macon, GA
www.dkhentertainment.com
I can only speak about Mackie subs, because that's what I have. Usually when I would set up with 2 subs, I would put the left channel into the left input of one and the right channel into the right input of the other. Then, daisy chain the tops out of that. My buddy, Steve Lynch, who let me borrow the other 2 subs Saturday, told me he called Mackie and they suggest you run both channels into 1 sub and then come out of the full range into the other sub. The tops can come out of either. That's what I did on Saturday and you can really hear a difference.

According to Mackie, when you only plug in 1 per sub, you get just over 1/2 of the available power, not 100%.

Have a profitable week!! :sqlaugh:

Kevin
 

Attachments

  • mackie back.jpg
    mackie back.jpg
    64.7 KB · Views: 2
Here's a question.....On the back of my subs, there is a "phase" switch. When would you use anything other than normal??


From the manual(http://www.mackie.com/products/swa1801z/pdf/SWA1801z_OM.pdf)

PHASE
This switch reverses the polarity of the subwoofer output. Depending on the placement of the SWA1801z subwoofer relative to the full-range speakers, you may get a better low-fre quency response in the room if you reverse the polarity of the subwoofer’s signal. Experiment with this switch to determine which position sounds best.
 
Thats kinda werid!

But I guess its worth a try!!


How come on the Mackie manual, they suggest a little different then??


I'm a little confused, but I am willing to try this, it doesnt hurt!
 
This brings up a basic question. I have a gig where I will be running 4 JBL EONS tops, and 2 JBL JRX Subs. I have never set-up more than 2 Tops and 2 subs. Having just the 2 Subs I can send the Audio directly from my DBX Croosover to each Sub, but the Tops I have to send to the First then.......I know there is an output jack, do I send that to the input on the outside Tops. Is there anything else in the set-up that I need to Do?
 
Thanks Kevin. I have the similar RCF 15" sub and am getting a twin this Wednesday. I would have hooked them up as you origianlly would have and never would have thought about doing the suggested method.

I assume that most people that don't couple their subs and instead place them under their tops are only running one xlr cable to each sub and then running to the tops. Who knew it was wrong. lol
 
run both channels into 1 sub and then come out of the full range into the other sub. The tops can come out of either.
Have a profitable week!! :sqlaugh:

Kevin


Thanks Kevin, So still plug in you 450s like normal? You will have 1 450 plugged into the 2 subs say running left side and the other 450 one plugged in by itself running right side? Sorry, I'm a little confused! I have been running(by the book) since I have had these...thx
 
I was never really happy with the 15's since I bought them... I called mackie, and talked to them, asking why they seemed kinda' wussy, and they told me that I was not getting the full potential of the amp if I was only using the input on one side.. he said that by running both inputs at once, I'd be taking advantage of everything it had..

It really seems to make a difference with the mackies!

Now I thought that carried over to the B-52 subs, but b-52 said no.... they auto couple the inputs if you only have one input fed...

JBL however says to use both inuts also...

try it, if it doesn't do anything for you, then no harm done... if it does, you should notice a pretty decent increase in thump!
 
is this just from experience, or otherwise?

Avi and Daniel have both told me that it didn't matter on their active products...

I've never been happy with my b-52 active stuff though...

well, I take that back, I own 10 matrix systems, and I wouldn't trade them for the world....

but my self powered subs have never worked as good as I imagined they would..
 
This brings up a basic question. I have a gig where I will be running 4 JBL EONS tops, and 2 JBL JRX Subs. I have never set-up more than 2 Tops and 2 subs. Having just the 2 Subs I can send the Audio directly from my DBX Croosover to each Sub, but the Tops I have to send to the First then.......I know there is an output jack, do I send that to the input on the outside Tops. Is there anything else in the set-up that I need to Do?

That system sounds VERY underpowered in the bass dept.

One JRX sub is 300 watts RMS, Two JRX subs would be 600 watts.

(By comparison, I would use two B-52 ACT-18's with 800 watts EACH, for a total of 1600 watts RMS)


I've been VERY happy with the two self-powered B-52 ACT-18's but I don't use the "Master-Slave" configuration (one powered and one unpowered) because I've heard other DJs having problems with the digital amp running 4 ohms (600 watts per box).

My configuration (both ACT-18's have their own amplifier) ensures that each box gets a full 800 watts RMS, which also gives you another back-up too!
 
I can only speak about Mackie subs, because that's what I have. Usually when I would set up with 2 subs, I would put the left channel into the left input of one and the right channel into the right input of the other. Then, daisy chain the tops out of that. My buddy, Steve Lynch, who let me borrow the other 2 subs Saturday, told me he called Mackie and they suggest you run both channels into 1 sub and then come out of the full range into the other sub. The tops can come out of either. That's what I did on Saturday and you can really hear a difference.

According to Mackie, when you only plug in 1 per sub, you get just over 1/2 of the available power, not 100%.

Have a profitable week!! :sqlaugh:

Kevin

Amazing idea. I own 2 1801 and I am going to try this setup early before the guests arrive and see if there is a difference.
 
Either I dont know what I am doing or....

I didnt seem to notice a "drastic" difference!

I ended up running them as recommended, and that works for me!


But I wouldnt mind reading other people noticing something!

Thanks!