How many Ohms? I'm stupid!

To many ads? Support ODJT and see no ads!

LoudspeakerDJ

New DJ
Nov 16, 2006
116
0
48
If I wire from my amp into 1 8ohm 18inch sub, out that same sub and into another of the same, how many ohms is on the amp?

I'm stupid when it comes to things like this!
 
So, how many watts would be driving each speaker if my amp runs 830 watts in 4 ohms? Would it be 415 each? Would this be a dumb thing to do?

I don't want to buy another amp for the not so often periods when I use my 2 subs, but have a qsc rmx 850. Can I drive the subs this way?
 
It depends on the specs of the subs. Running the RMX bridged as you mentioned will give you 415 w per sub.
 
I don't see why not.

With two identical cabinets on an amp feed, each cab may be considered to be receiving half the amp's output dissipation at the combined impedance. It should work well for you.

If you find that 830 WRMS is not sufficient for your sub cab needs you may wish to look at investing in a more powerful amp for the subs. Your current amp may be utilized for mids in a bi- or tri-amped configuration. :)

Remember, your power dissipation will halve when running just one sub cab at 8 ohms load.

Hope it helps.
 
ImpedanceChartSmall.jpg
 
Why dont you run both subs off the amp directly rather than jump them? If you are running more than2 speakers off the same amp you are changing the load again
 
Why dont you run both subs off the amp directly rather than jump them? If you are running more than2 speakers off the same amp you are changing the load again

I am brainstorming outloud. My plan is to run the amp bridged, since it doubles the wattage at 4 ohms. running stereo at 8 ohms into eah speaker the wattage is worthless. I obviously would like a more powerful amp, just trying to buy some other things at the moment. Was hoping for the few times i need the subs (rarity here) that I could use the extra amp I already have.

When it comes to the specifics od ohms, watts, amps, all those things I really have very little idea! I need to take a class or something.
 
I am brainstorming outloud. My plan is to run the amp bridged, since it doubles the wattage at 4 ohms. running stereo at 8 ohms into each speaker the wattage is worthless. I obviously would like a more powerful amp, just trying to buy some other things at the moment. Was hoping for the few times i need the subs (rarity here) that I could use the extra amp I already have.

When it comes to the specifics od ohms, watts, amps, all those things I really have very little idea! I need to take a class or something.

Actually, your theory is a tad flawed here. I'm going to ask Fred to back me up on this with fact since he is the resident electrician.

When you piggyback your subs one to the other, this is when you increase the load to 4 ohms from 8. When you "bridge" your amp, you are effectively using only one side of the amp, but sending all the power it can muster into that single load. So you aren't really doubling the power so to speak.

If you put your amp into "bridge mode" and run both subs piggyback at 4 ohms, it is true that you will send a "cleaner" and more efficient amount of power to that load, but I would be very careful about the levels I would try to achieve. Unless you are using an active cross-over unit such as the Ashly XR1001, which gives you greater control over the frequencies you are sending to your speakers, and some sort of limiter unit prior to sending the signal to your amps, you could very easily over drive the amps into clip mode and then into a "thermal" meltdown situation. You would also wind up losing headroom and if you send your amps into clipping, you increase the distortion load ten-fold.

If you bi-amp your set-up (which is what I recommend) you would have much greater control over the SPL your speakers are worthy of producing.

Again, I want Fred to chime in on what I have said to make sure I said it correctly. I hope I was able to keep this post in pretty much laymens terms so that you would understand what you are up against.
 
Actually, your theory is tad flawed here. I'm going to ask Fred to back me up on this with fact since he is the resident electrician.

When you piggyback your subs one to the other, this is when you increase the load to 4 ohms from 8. When you "bridge" your amp, you are effectively using only one side of the amp, but sending all the power it can muster into that single load. So you aren't really doubling the power so to speak.

If you put your amp into "bridge mode" and run both subs piggyback at 4 ohms, it is true that you will send a "cleaner" and more efficient amount of power to that load, but I would be very careful about the levels I would try to achieve. Unless you are using an active cross-over unit such as the Ashly XR1001, which gives you greater control over the frequencies you are sending to your speakers, and some sort of limiter unit prior to sending the signal to your amps, you could very easily over drive the amps into clip mode and then into a "thermal" meltdown situation. You would also wind up losing headroom and if you send your amps into clipping, you increase the distortion load ten-fold.


If you bi-amp your set-up (which is what I recommend) you would have much greater control over the SPL your speakers are worthy of producing.

Again, I want Fred to chime in on what I have said to make sure I said it correctly. I hope I was able to keep this post in pretty much laymens terms so that you would understand what you are up against.

This is good information, thanks. The amp I will be driving the subs with is running in 8 ohm stereo at 370 watts, but bridged mono mode in 4 ohms at 1680 watts. that would be 840 per sub.

You know, I'm not sure what my point is here, other than I'm just throwing a bunch of stuff together. I was always under the impression, that you wanted a bit more power than the speakers program rating. Is this a good rule of thumb?

I do use a crossover, so as not to use the on board crossover in the speakers. Hopefully that helps a little. I certainly dont want thermal shutdown (I've never had this before with my qsc 2450 amps even though the clip light illuminates from time to time) and I certainly don;t want to blow my speakers out either.
 
Actually there are several misconceptions here.

"Piggybacking" (parallel) connection of two 8 ohm speakers will be a 4 ohm load.

Bridging the amp. What you are doing is making both rails on the "A" side positive and both rails on the "B" side negative and vastly increasing the power, efficiently using the entire amp.

Chances of clipping an amp when you have the power available are a lot less than when you have too little power, so in the bridge mode the headroom will be greatly increased.

You are correct, you want all the power you can get to the speakers up to the peak rating. at the minimum you want at least twice the continuous or RMS rating. For subs this is almost a requirement to get a decent response from the sub.

BTW run a seperate line from the amp to each sub do not jack from the amp to sub #1 and then from sub #1 to sub #2. Doing so runs all the power through the first jack on sub #1 and it increases the amount of cable the power will have to run through to get to sub #2 there by affecting the damping factor of the amp.
 
Excellent advice. :)

Two 8 ohm cabs connected in parallel will give you a 4 ohm load. Since subs are omni-directional they don't need to be run in stereo. Bridge your sub amp and, if you have to make up a custom pigtail for it, run both sub cabs directly from the amp's bridged Speakon output jack.

Occasional clip LED flashes tell you that you're reaching your amp's maximum capacity. If it still ain't enough don't push it. Look to invest in a more powerful amp and/or sub cabs that can handle the shows you're doing.

True... a sub cab's rated RMS or Program should be fed with double amp power dissipation capacity. This is where your system headroom comes from.

Agreed ~ a compressor/limiter really should be a part of the processing chain. There will be differing opinions on this, I understand. However, I recommend a C/L in your system to protect against a dropped mic blowing your horn drivers.

Hope it helps. :)
 
Okay... so I 'm pretty late on this thread.. but thought I'd post a document I wrote up that breaks down Ohms and some quick ways to calculate them. Now, those of you who are Electrical Engineers out there, don't nit-pick. I tried to keep it in simple terms!

http://www.northernlightfx.com/tech/Ohms.pdf

Ben
 
One thing I'd like to add... loudspeakers and power amp load specs are rated in ohms impedance, not ohms resistance. The two are calculated in the same manner as Ben illustrated.