Numark TT200 turntable advice wanted.

To many ads? Support ODJT and see no ads!

Ed Witles

Active DJ
Nov 6, 2008
716
34
62
Gang -

I bought one of these used if for no other reason, 78 speed.

I want to archive my library of 78s (and of course vintage 45s and LPs).

Well, seems the unit has a minor hum on the right side. Only when the playback volume is maxed do I hear it.

Yet it still 'appears' on the recording. 78s are ok, but for other, is not.

The factory integrated headshell (all in one) is rather quiet but EVERYONE of my other headshell mounts have noise.

Yes, the wires are correct. Yes, I changed turntables.

From Ortofon to Grado to Pickering... all yield some noise. If I remove the right RCA, it is quiet.

So my question to you guys, are these turntables inherently noisy?
 
Yes, I am using a high end preamp - not a DJ mixer.

I even swapped RCA w/ gnd wire.

I am thinking some funny biz inside.

I even swapped the S arm w/ the straight one. In fact, plugged the headshell into the arm at the pivot point.
 
I just found this...

the numark tt200 was very sensitive to the interconnect cables if i remember correctly so maybe a bit of experimentation may help the hum and tonal qualitys as the cable + cart is what the phono stage sees in the load sense.

and...

Numark TT200's that don't like high inductance/impedence designs and induce hum on unshielded cartridges (from the power supply).

Sigh.....
 
Sigh...

Well, I just ordered a genuine Numark headshell so we shall see. It's a great unit - but noisy. Grrrrrrr.

I'll hafta look for a shielded audiophile cartridge w/ a 78 stylus option.

Hopefully, someone else was helped w/ my tale of woe. :D
 
Checking around, it seems your problem (hum on the right) is common among owners of the TT200. More than one person has complained of it .

I attempted to download the manual from the Numark site but unfortunately they want to know who is receiving their state secrets. Another demerit for Numark. This unit has integral (permanently connected) RCA cables and a USB connection?


http://en.allexperts.com/q/Audio-Systems-835/2008/7/turntable-hum-1.htm


Amazon.com: Numark TTUSB Turntable with USB: Musical Instruments@@AMEPARAM@@http://ecx.images-amazon.com/images/I/4148weUBVCL.@@AMEPARAM@@4148weUBVCL

Typically what I'd do now is pull out the DMM and compare one side against the other and each line RCA to headshell. If this has a built in sound card that may not be possible. It was typical to get a little hum if one of the connections has some resistance. Headshells were the biggest offender but the RCA connector inside the TT base could also cause problems. A little contact cleaner of even just inserting and removing a time or two could do the trick.

Good luck.
 
Actually, more like a buzz vs a hum. I took the unit apart and tightened the ground screws all around. Verified the ohms from gnd lug to the black wires going into the arm assy.

The unit is wired like this...

The L & R, + & - are separate from the ground wire. Not sure if that is correct or not - but almost makes sense.

One thing I noticed... although it uses a 3 prong IEC plug, the 3rd pin is not connected on the I/O board.

I might have to troubleshoot w/ it connected to an amp and start tracking down the ground till the buzz goes away.

Even the integrated seems a tad buzzed, but not as bad as the headshell.

I might just bite the bullet and use a nice B&O unit and software upconvert my 78s from 45 speed since I don't have room for both. That will take forever. :)

Sigh....