Best deal on vertical truss with base for moving yoke.

To many ads? Support ODJT and see no ads!

stevet

New DJ
Nov 28, 2006
33
0
68
I'm interested in buying a 6 to 8 ' in length, square 12" truss with a 24" base plate. The top end needs a standard 12" square plate.

I'm looking for two for now, but plan on buying four to six more over the next year.

Here's what I've found so far:
3157.jpg


These are selling for $500.00 each.
I'm hoping to find a better deal. Anybody stumble upon a great source, and a great deal.
 
Have you checked e-bay?

I've seen a set of three box truss sections for about $775 with free shipping on e-bay. Actual photo is below.

I'll post a picture of a very short section with the cross brace I also made myself. My plates will fit on the top or bottom. Cost me under $50 for eight plates and misc hardware. I already had the truss. I can mount the cross brace anywhere along the upright and have my horizontal truss come off of that. I can use a bolt or a "D" pin to attach the plates to the truss.

I think $500 is a little high, but it depends on how bad you want it, and if your handy enough to do it yourself.

However, your picture looks like heavier truss and a bigger plate than mine.
 

Attachments

  • 5foottruss.jpg
    5foottruss.jpg
    19.9 KB · Views: 3
  • Parts.jpg
    Parts.jpg
    69.1 KB · Views: 3
Thanks Tyrone.
I did try Ebay.
I've thought about doing it myself, but will probably end up just buying it.
 
It really depends on what you're going for. Global Truss is pretty affordable, the other brands we carry (Tomcat and ITTC) would be many times more than $500, but that goes more to tour users.

I can get you a Global 12" square 6.56' truss section with a 12" aluminum top plate and a 24" steel base plate for $381.25 + freight.

Bear in mind that the raw costs of aluminum have not been kind to the industry and that prices are not declining, but rather increasing. Waiting for a better deal may backfire.

Ben
 
I can get you a Global 12" square 6.56' truss section with a 12" aluminum top plate and a 24" steel base plate for $381.25 + freight.

sounds like a good deal, but I'm using a Dodge Caravan (short bed) to transport my gear....must...see......out......rear view mirror.

I have to weigh the option of using my "passive" tops (2 SR-quality trapezoidal cabs with 15" JBL 2220-h drivers & 2" titanium compression horn).

Seems more cost effective to use the speakers as the base, although I must consider the extra lifting, weight, and bulk of the Crown amp and the 85-pound SR-cabs.
 
Bill,
How much for that same arrangement, but with the
Global SQ-4112-215 (7.05') square truss.

So,

SQ-4112-215
12" square top plate
24" steel base for square truss.

I recently purchased two of these arramgements, but will need two, or maybe four more sets.
Delivery is to area code 85222 (AZ). Global will drop-ship. Oddly, they come to AZ in one day!

thxs, Steve
 
Bill,
How much for that same arrangement, but with the
Global SQ-4112-215 (7.05') square truss.

So,

SQ-4112-215
12" square top plate
24" steel base for square truss.

thxs, Steve

I recently purchased two of these arramgements, but will need two, or maybe four more sets.
Delivery is to area code 85222 (AZ)

Sorry Steve you meant Ben right?
 
You can call me anything you want... just not late for dinner. :)

I'll get pricing on that worked up for you tomorrow and PM you. I have some meetings out of the office in the morning, but should be on it in the afternoon.

Ben
 
Ben...

Just so you know, I am considering several sections of Global 12 inch box and two of their 18 foot crank ups. I've been watching them on e-bay and the prices are a little out of my range right now.

Maybe next summer, but if something used or discounted shows up, I'll make the road trip.
 
Well... I'll tell ya what... I don't have the SQ-4112-215 in our priceguide, but the part I quoted earlier was the SQ-4112... so I'd guess at MOST it's a $20 or $25 difference for the -215. I'll be at NAMM next week and I'll be sure to double check that with GT, but for now... you can hold me to the $20, if it turns out to be more I'll eat it.

Ben

How much for that same arrangement, but with the
Global SQ-4112-215 (7.05') square truss.

So,

SQ-4112-215
12" square top plate
24" steel base for square truss.

I recently purchased two of these arramgements, but will need two, or maybe four more sets.
Delivery is to area code 85222 (AZ). Global will drop-ship. Oddly, they come to AZ in one day!

thxs, Steve
 
Whats the general feel on Applied Electronics Truss? I have two 5 foot sections that I've been very happy with. The only down side is that the pipe is 1 3/8 inch vs 2inch. So you need real touring clamps or a space filler.

So is the stuff just too expensive for the DJ market or is there a reason they didn't saturate?
 
Pete
My guess would be too expensive for cheap DJs and too cheap for those looking to buy 'the good stuff'. It's not standard diameter for many clamps, so not of interest to me. The Global Truss is, IMO, about the best durable, tightest connecting truss on the market under the touring rigs with much larger price tags. We'll be buying some in the next year or less ourselves. Our old 1" tri is getting pretty worn out!
 
Thanks Ben, I'll be looking to buy in three weeks.
The Global truss is some of the best for the $$
I'll look you up.

Moving heads look and work great sitting on these 7 ft stands.
I'll upload some pixs.
 
I both sell, and own a bunch of global truss... the truss isn't the cost, it's the shipping! It's stoopid expensive! I'd love to sell you some, but I also would like to give you some other options.....

If you're looking for vertical moving head stands, but the $59.00 triangle truss from cheaplights.com, make your bases like many of us did from parts at home depot, and wrap those babies with spandex socks with led light inside...

you'll be in business for less than $150.00 and it will serve the exact same purpose, as well as look just as nice...

just a bargain stand tip!
 
Thanks Steve.
Those stands are a good deal.

I'm not sure how sturdy they would be when a 40 to 50 LB moving head is thrashing about?

Does anyone here have the "road map" to making these cheap with a solid steel base (like the global 24" square steel base). Also would need a 12" square top plate to mount the head on.

thxs, Steve
 
If you're looking for vertical moving head stands, but the $59.00 triangle truss from cheaplights.com, make your bases like many of us did from parts at home depot, and wrap those babies with spandex socks with led light inside...

you'll be in business for less than $150.00 and it will serve the exact same purpose, as well as look just as nice...

just a bargain stand tip!

THANK YOU for the wonderful suggestion.

Now I must find someone who's experienced in Metal Working (handy with a welding torch).

It makes me wonder why Cheaplights hasn't come out with a flat "end piece" that fits into each side of the truss section. If you sold the sections as Knock Downs (assemble at home with Allen wrench)....it would save on the exorbitant shipping costs.