truss structure

To many ads? Support ODJT and see no ads!
Maybe I didn't mention I fabbed this up in my welding shop. If I can fab up structures to hold 2500 lb transformers and get insured and certified by OSHA, EMSHA, and onsite engineers for safety and structural integrity a little 1" tubing to hold up 100lbs or less of lighting is not that big of a deal. I made the base plates out 1/4" steel plate 12" x 24". I was thinking about putting a layer of MDF under them to keep from scratching up people floors, but as I was saying Not sure if I am going to use it yet or not.
I have some schedule 80 aluminum tubing that might make the whole thing a lot lighter and easier to handle.
 
Very industrious.... It might be a bit too tall.... some venues might only have 8' ceilings....

Take some pics so we can see what ya's done.

I thought about that, but 8' just seemed so low. If I make it 7'6" and hang a 12" mirror globe from the bottom. 3-4" for hanging mechanism ..etc....that puts the bottom of the globe 6'2" or so......would that be glaring into people eyes?????? Or is it not that noticeable.
 
you have all these madd skillz and yet you want to run cheap extension cables for the lighting? You must be able to get high grade cable on a spool to make the right stuff at a considerable savings.
 
you have all these madd skillz and yet you want to run cheap extension cables for the lighting? You must be able to get high grade cable on a spool to make the right stuff at a considerable savings.

Maybe I said that wrong.....I don't want cheap....I want inexpensive.... I can get 14/3 SJO Cord, (That is a medium jacketed industrial cord, and its rubberized not vinyl so it is extremely flexible and durable and good for around a 15A load) for around $.28 a foot. But they really rack you on the cord ends I need 20 cords around 20-25 ft long to power up all the lights. If I made them I would make custom lengths to where I normally set up the gear so it would vary.....so say 500ft of cable ....that's $140 not to bad for a good heavy cord. Then come the cord ends at $7.21 each....and these are not clean neat molded ends they are heavy duty....I seen get run over by a truck and be just fine....so quality is not at issue, but 40 cord ends is $288.40...grand total $428.40 for cords. If I can't find anything for right price, I may get a 20 conductor cable and basically run one cable for everything. Put multiple male end on one side and a bunch of outlets in the truss......a little more complicated than that but that gives you the jist of it.

I just hate putting that much faith in one cable... Experience tells if it is imperative that one thing must absolutely not fail.....when the system quits...start there.
 
Safety and Reliability = $$$$

Yes, the plugs may be expensive but they will do the job and you know you can trust them. Once again it's the USA and lawyers are worse than sharks in smelling the weakest link. If the truss or connectors were to fail (Using a cheap connector or cheap extension chord will put you in the hot seat but with the quality stuff you're still not out of trouble but the flames being deflected makes things a little bit better) ;)
 
Safety and Reliability = $$$$

Yes, the plugs may be expensive but they will do the job and you know you can trust them. Once again it's the USA and lawyers are worse than sharks in smelling the weakest link. If the truss or connectors were to fail (Using a cheap connector or cheap extension chord will put you in the hot seat but with the quality stuff you're still not out of trouble but the flames being deflected makes things a little bit better) ;)

I can assure you that under normal circumstances and even some extreme circumstance the will not fail. And again I mis-phrased my question. I was a reliable cord at a reasonable price. The kind I deal with are way overboard for a few lights. Do you really need a Ferrari to drive to the grocery store? or will a chevy do just fine.
 
If you had to estimate cost.... including your labor how much did fabricating a truss system really cost you?

I can get a rectangle Mobile DJ truss system for about $700.00 with transport bag off ebay.

Not counting my labor I have a total of $24.00 invested so far. All the materials I used were left over from other projects. My 5 hours labor isn't prudent but I bill out at $100 hr, but that's for an Industrial Electrician. But most welders around here are $50 hr. I will spend another 2 hours putting an industrial epoxy paint on it.

This is not something most people should do I guess. But I get paid to do this kind of stuff.... I get presented a problem....then its up to me to make it work the way the customer wants it to. Sometimes I have to fabricate custom pieces..I do a lot of work with PLC design and programming now days. There is a water treatment plant a few miles from me that is running on a system completely designed and installed by me(electrically/computer). It's just what I do.
 
The antenna is not designed to carry horizontal loads. They're quite common down here and you should see them sagging.


A wind load is horizontal. Before you say they're guy wired, some are telescopic without guy wires. A good part of the reason for using a truss tower is they don't need guying at the very top due to the lateral stability. Just like anything else, not everything is created equally. There may be really bendy (that's a technical term) ones out there.
 
I put a 500 lb load on it this afternoon after work.....no problems....no flex....the end didn't toe out......I was actually impressed....I didn't think it would hold that but....This is an old tower put up in the 60's that was 100' tall plus mast......we took it down with our bucket truck a couple years ago......structurally it was in quite good shape.....I was skeptical when I started messing with it....But now I think I am getting attached to it. If nothing else it will work until this Business makes enough to be self sufficient.