Speaker questions...

To many ads? Support ODJT and see no ads!
G

Guest

Guest
I did a high school gig last week and used the following system: Mixer, into a crossover, lows into one amp that fed to two subs (right and left). Mids and highs into another amp that fed into two 2 ways (right and left).

The system was pushed to the max (just barely into clip), and I wasn't happy with the output. I got the job done, but I wasn't happy.

Here's my questions: all four speakers were 8 ohm. If I had added two more subs and two more 2 ways, which would have resulted in a 4 ohm load, would I have gotten more/better sound?

How could I have used even more speakers with two amps, if at all... I'm guessing I would have to add more amps when I exceed four speakers on one amp? Is four speakers (8 ohm) the most I can put on one amp? If I had 4 ohm speakers, would that have been better?

What exactly is a "line array"? Is a typical line array consist of powered speakers? How/why is it different than a conventional speaker set up?

I'm looking at some JBL's (2 ways and subs). Are these good, or should I look at something else?

Remember, I'm a novice when it comes to sound gear, so keep it simple.... Thanks in advance.
 
I don't have a clue...

I have the ability to plug in another speaker to all of mine (two jacks on the back of all of them), so I'm guessing that I can daisy chain them, but I don't know how many speakers I can do that with. I'm guessing I can't use more than four speakers on one amp...correct?

I don't know what bridging is or how to do it.

Can someone tell me what (if anything) is wrong with Pyle speakers? There's a lot of them on e-bay and I've heard a lot of "put down" posts bout Pyle... how about an honest post on Pyle speakers?
 
I Used to Sell Pyle / Studio Pro

Sound is Great! When I started worring for a Mulit Op
All 35 DJs had Studio Pro / Pyle Speakers
From the 12' to the Dual 15s
12" 15" 18" 2x15"

The Only Issue I had with The CABs was that from the 15s + I had to reinforce the Backs from the Inside, they Rattle alot from the Back

CD Players I didn't Like (They did have Sony Decks inside, - this was fine)
The Outside parts always fell off
Amps were decent after the PA1000
 
Assuming you use all 8 Ohm speakers:

2 speakers=4 Ohms
4 speakers=2 Ohms

If you bridge an amp, it automatically sees a 4 Ohm load, so you should only hook 2 speakers up to it.

Not sure what amps you run, but here's the specs on my Crown CE2000 to give you an idea how much more power you can get by adding speakers.

Stereo
400W/ch @ 8 ohms
660W/ch @ 4 ohms
975W/ch @ 2 ohms

Bridged Mono
1,320W @ 8 ohms
1,950W @ 4 ohms




Be warned that when you run an amp at lower impedences, they have to work harder, therefore they run hotter.
 
OK, I think you answered my basic question...

So, I'm in the market for two more subs and two more 2 ways. I like the look and price of the Pyle PASW 18 (about $130) , and the PSWB 15 (about $199). Any feedback?

Now, can anyone explain a line array to me?
 

Attachments

  • PASW15.jpg
    PASW15.jpg
    72.6 KB · Views: 0
  • PSBW15.jpg
    PSBW15.jpg
    35.4 KB · Views: 0
Yep...

I only have one powered sub, and I use it on my gig bench, where it still is. I have a total of 13 speakers. I have four that are dedicated to my club gig, and always stay in the club.

Four more are my traveling speakers (the ones in first post). I have 4 powered 2 ways, that are not being used right now (also use with my gig bench during the summer).

This whole issue started while doing the high school gig (from first post) and I am looking for ways to put a little "umpf" in my sound, without spending an arm and a leg.

The traveling subs are "Com" speakers that I have no idea about quality. These are the ones I picked up the day my normal subs blew up at a gig, when bringing in from the cold. They are nice compact subs and seem to work very well, even though I've never heard of them before.

I have EV tops that I mount on the Com subs (see picture). My preference would be to match these four with the same speakers for the "look", but price is an issue right now, which is why I'm investigating Pyle's.
 

Attachments

  • traveling gear.jpg
    traveling gear.jpg
    80 KB · Views: 6
Line Array by definition is a group of speakers stacked up on a vertical plane.

The use of a line array provides higher db levels at the rear of a room than a conventional speaker system. The line array system will still provide hot areas closer to the source but more dispersed though out the room. Without side fill the sides of the room will have lower db levels than the rear of the room.

A conventional speaker system is hot in the front of the room and fades to the rear.

A Bose PAS is an example of a mini line array system.

It truly sounds like the spl levels of your speakers are not high enough to satisfy your demand for sound. I myself enjoy to be loud as possible.

I ran a set of JBL EON 1500's for a while spl 98 db. Not near enough, my Turbosound 15" are 130 db the 12" are 128db. The 18" subs are 129db.
 
I don't know much, but from your picture, the first thing I would say is take the subs off the dolly and have them on yje floor... I know it's harder, but it should make a difference I think...

I don't know about the brands you are asking about, but it is always better to wait a bit so you can spend a little more and get better stuff....

Untill I bought my BOSE I was running dual 18" Peavey subs,, 2 18's in each cab and I was powering each cab with a QSC 3402 Bridged mono

I had the Peavey two way tops that had 1 QSC 3402 stereo.. had loud thumpy sound, but nothing like some of these big ass systems I see posted...

I also ran my shows by myself so I had to figure on the set up as I bought
 
The 18's you are looking at are 97db the 15"s are 102db.

I wouldn't buy speakers under 125db. They just will not perform.

It pays to buy good speakers. Tyrone you have a ton invested in lighting you should have even more in sound.

JBL JRX 18"s would be a better option than the pyle speakers you are considering. Or Peavey 18"s are another less expensive option.
 
Tyrone,

Cameron is right on...you have an amazing light show. Do you really want to use Pyle speakers that cost a couple hundred bucks for your sound??

IMHO you would really be doing your self a diservice by using those speakers. You have been in the business long enough to know that quality sound is not cheap. Do yourself a favor and invest in speakers that are going to compliment your show, not diminish it..just my $.02
 
Good info Guys

Most of the information you are getting here Tyrone is pretty good. I’m not going to venture into the marshy land of one speaker vs. another but the price on that sub seems awfully low. The bare driver (sub) I bought from Parts Express cost as much as that 15" sub and it was a 12". Massive magnet though, that screws up the color TV from across the room.

There are whole books written on line arrays so to put it simply, Cam described it pretty well. The design tries to develop a cylindrical wave front rather than a spherical one. The idea is to carry the sound deeper, shape the sound dispersion to the shape of the room. You would not like the price nor the problem of carrying the gear.

Chuck brings up an interesting point for a little more bottom couple the subs with the floor. Putting them directly on the floor will help a bit.

Jay answered an earlier post on bridging. He was spot on about bridging, it halves the minimum impedance load your amplifier may drive. Adding a second speaker to an amplifier output will increase the power at the output. Unfortunately, it will also make the amplifier work much harder. I’d prefer to see another amplifier driving the speakers if the funds are available. It adds some redundancy and doesn’t stress the gear (amp) as much.
 
OK...

I asked about the Pyle's and got the answer. Thanks. I will stay away from that gear. As far as bridging goes, I still don't understand what to do. I'm certain my amps are set up for stereo.

For now, I'll look for the same quality speakers and hook them up to the other jack on the speakers I have, for 4 ohms. I am currently using two amps and don't think I'll promote my show for venues that will require more than four subs and four tops.
 
Tyrone,

Using 4 speakers has issues too. The horns can easily interfere with each other if they aren't splayed correctly. Some sound guys will take the second pair and mount them upside down on the first pair. This way there are no cancellations in the horizontal plane.
 
Using 4 speakers has issues too. The horns can easily interfere with each other if they aren't splayed correctly. Some sound guys will take the second pair and mount them upside down on the first pair. This way there are no cancellations in the horizontal plane.

Hi, sawdust.

I use four speakers. I have never had any issues--at least, none that I'm aware of. What obvious difference should I notice if I put the top ones upside down?

Thanks.
 
It depends on how they are set up. I sometimes see them put side by side facing the same direction. That is fine with subs but you can get all sorts of mid and upper range lobing when you do that.