Sound Techs.... Question???

To many ads? Support ODJT and see no ads!
G

Guest

Guest
OK, I have a tech question and I don't have a clue how this all works.

I purchased 8 speakers from Bernie Howard last fall, and I'm ready to fire them up (now that it's warm outside). The speakers are: 4 duel 18 subs and 4 tops (check the photo).

The amps are: three Crown K2's which are hooked up to a crossover. The way he set it up is to have only one amp going to all the subs and one amp to two of the tops and the last amp going to the other two tops. I think he only had two subs when he hooked up his amps that way (and added two more subs later on , but never had them in the mix). The back of the amp rack is FILLED with speakon outputs (and wires everywhere), and I don't have a choice as to the connections (the way he had it wired).

Anyway, the amp rack is all wired for "speakons" (and the K2's have banana plugs in the back for output).. Here's what I'd like to do and don't know how to start. I'd like to add one more amp, so that there are two amps for the subs and two for the tops.

I'd like to keep the crossover involved. I don't know anything about mono bridged or stereo outputs. How do I go from the banana plugs to the crossover to the speakers (speakons)? Remember... I know nothing about sound, so go easy on me.

I'll get a picture of the back of the amp rack later today and post it.
 
Oh, I forgot the pictures...

Here ya go
 

Attachments

  • JBL SR STACK.jpg
    JBL SR STACK.jpg
    131.4 KB · Views: 14
  • Crown K2\'s.jpg
    Crown K2\'s.jpg
    28.2 KB · Views: 130
More info Tyrone!

The K2 is 2 ohm capable. This means it can run up to four 8 ohm speakers in parallel or two four ohm speakers

Formula assuming all speakers are the same impedance and connected in parallel:
Impedance = speaker impedance / # of speakers

When the outputs are bridged, the minimum impedance an amp can drive is doubled so if the subs are 4 ohms only one can be connected to a K2 (bridged) output. A bridged K2 is now a mono amp capable of roughly twice the output (with only one channel). I don't see any reason to use bridging in your configuration unless you are going to invest in a lot more amplifiers.

I think you are close, but I’d like to see you tri-amp these puppies. Connect a K2 output (side) to each of the subs so they could pretty much loaf along. Hook up each of the tops in a bi-amp configuration, each driver with its own amplifier channel. You don’t need as much muscle for the high frequency drivers and could buy less powerful amplifiers. All this should be given considerable consideration before laying out more money. The only other addition would be a nifty active crossover like a Berringer DCX2496.

As an alternative as you suggest “just” buy an additional K2 and run each top using each speaker’s internal passive crossover.

If we get Fred in here he’ll be chanting tri-amp, tri-amp in short order and he’d be right.

You really have to provide some more info like either the model# of the tops or the input impedance and whether they can be readily bi-amped (I'm guessing they can). What I believe you're thinking of doing will work as well.
 
Holy Crap!!! I Know A Couple Bands That Would Kill For Those Cabs And Amps!!
 
if 1 amp powers 2, just jump the audio signal from the the first low end amp to the 2nd. i personally would tri-amp the system for better frequency response, but i'd also put a high end PA processor in there. kv2's are sweet amp's though, and those boxes sound great.
i should post some pics up of my x-array...
 
Ahhhh, what???

Balanced, you already have me lost. I was wondering if I should change the configuration of the outputs.

Like I mentioned, the amps were previously set up so that only one amp is running the subs and the other two amps have the tops (two each). Bernie told me he did this in case he lost an amp, he'd still have tops.

In MY way of thinking, I'd think that the subs would require two amps and the tops only one (not the other way around). When you mention bridged versus stereo, I"m not too sure how that works.

So, If I got one more amp, how do I run cables to each of the speakers... what sort of cables and where do I plug them in considering the crossover?
 
Sorry Tyrone,

Without pictures and diagrams it is hard to get some of these ideas across.

As you go up the frequency spectrum you need less power per octave. This is one of the reasons multi-amp configurations are ideal for high power applications. Passive crossovers are usually to be avoided in high power applications (in this case, for your tops). That doesn't mean they will not work just fine.

As I read it, you were going to purchase another K2 amp? That gives you eight channels of amplification.

To connect the system with just one more K2 (4 total)
I would apply one channel, one K2 amplifier side to each sub.
I would apply one channel, one K2 amplifer side to each top.
This is the configuration I believe you intended and were asking about if you purchased one more amp. Right?

It is possible to connect all those speakers with just a single stereo amplifier, that doesn't mean it is a good idea. Having the ability of running down to two ohms gives more options. None the less it is best to be conservative in rating and configuring your gear. I'd rather see a minimum of a 4 ohm load on those amps. I asked for more details that you didn't provide Tyrone, therefore I have assumed all the speakers (boxes) are 4 ohms?

Two more smaller (stereo) amps, say, less than half the power of the K2s and with the addition of a good active crossover you could have a kick ass tri-amped system that would be loafing along at very high SPL.

Bridging was mentioned only because you asked about it in passing and because I didn't think it was a viable option in this case.
 
It looks as he (Bernie) has a EV signal processor in that rack already.

Can you post some pic's of the back of the rack?

The bannana plugs are OUTPUTS for the speakers.

There should be a bunch of XLR plugs on the back of the processor, that would be connected to the XLR INPUTS on the K2's.

The banana plug, to Speakon, Would be solved by making a banana plug jumper, to a rack panel with some chassis mount speakon's.
When labled correctly, it makes for fast, easy connections for all those JBL's

Should you need more assistance, I can be reached at (920) 858-4127
 
Basic connections for tops and subs

Tyrone here is a basic representation of what I believe you wish to do and basically what Bernie had done. You are saying that Bernie only powered up two of the four subs. You are considering the purchase of a fourth amplifier to do so. Correct?

The attached drawing represents only one channel. With your four tops and four bottoms the portion of the drawing after the active crossover, the amplifiers on, will be duplicated four times, Twice for the left side and twice for the right side.

The signal moves from your program source (not shown) to output, from left to right.

At #'s 1 and 2 the signals are balanced line level signals. To the right of the triangles (K2 amps) you would have a jumper from the K2 banana jack to the Speakon panel connector mounted on the rear exterior of your amplifier rack. Speakon to Speakon jack cables would then allow quick connection to your speakers.

Typicals for wiring Speakon connectors can be found on the Neutrik site
http://www.neutrik.com/content/products/level03.aspx?id=204_184671&catId=CatMSDE_audio
Click on the wiring suggestions link on the right for a .pdf

I'll assume you have already connected balanced line level signals using XLR and/or 1/4 inch TRS (Tip, ring, sleeve) connectors so that will not be covered here.

Adding four more amplifier channels would allow you to bi-amp the tops as well. You would then have a fully tri-amped system. There are advantages but strictly speaking is not necessary.

I hope this helps Tyrone.
 

Attachments

  • Tyrone_Bi_Amp.gif
    Tyrone_Bi_Amp.gif
    11.4 KB · Views: 15
Larry, I would strongly suggest tri-amping this system.

I am not familiar with Crown amps and what these units can do so I'll leave that one to those who know. We use Carvin DCM amps exclusively.

Four dually 18 cabinets is a lot of rumble. They'll need a lot of amp headroom to feed 'em. I am going to presume that these cabs are 4 ohms... and would suggest running 'em each with one K2 assigned in stereo (not bridged). I do not recommend running SR with 2 ohm loads.

This leaves a third amp (and an additional amp to be purchased later) to tri-amp for the tops. As Balanced Line mentioned, you do not need big, beefy amps for mid-highs. The additional amp will give you stereo capability for the tops as well. It will involve a lot of cabling and connecting up but it's worth it.

For my part, I would rip that rack bare and start over to set it up to my preference. :)
 
Those are the same JBL subs we are using in the club. They have parrallel neutrik inputs. According to Ty's original post, the rack contains (3) of the K-2's and an active crossover already.

Personally, if I were Tyrone and I were going to run the configuration as the pic with Bernie in it shows, (4) mains and (4) dual subs - I would definitely go ahead and purchase a 4th amp - for redundancy purposes.

The sub cabs have two 8-ohm 18" drivers in them with a peak rating of 3200 watts. Since the two drivers are paralleled already from the factory, this makes them 4 ohm cabs. Just as a rule of thumb, I NEVER RUN AN AMP LOAD HIGHER THAN 4 ohms. Any company can claim that an amp will run at a 2 ohm load all night (such as the Crowns or Mackies) but I'm the type that likes to play it safe and not push them that hard.

The Dx38 processor unit in Ty's rack has all XLR inputs and outputs. It is a digital processing unit that employs RACE software.
Here is what I was able to gather from Electro-Voice:

RACE software is EV’s professional audio solution for modeling the response of loudspeaker
systems both simple and complex within specific venue measurements, and for digitally controlling
such systems through the Dx38. RACE enables engineers to seamlessly integrate room
influence, speaker positioning, and parameter settings, and RACE system presets guarantee a
solid, accurate basis from which to begin system tuning.
EV obtains specific acoustic data for all of its speakers by measuring each speaker separately in
its large anechoic chamber and saving the information in a RACE-specific file. The user assigns
individual components to RACE outputs using these files, and applies desired filter, delay, and
level settings. RACE then calculates the complex summation of all settings applied to the components.
At a glance, then, RACE users can view not only each component’s (and the system’s)
electrical filter response, but also its true acoustic response! Any changes in parameters are
immediately visible and audible. As well, RACE can display SPL dispersion for lower frequencies.
System presets can be prepared offline in advance. The user can employ one of the 50 preinstalled
presets, or customize one from individual component files. Systems prepared in this
way need only a little tweaking once speakers are in place. RACE makes quick setups a snap!

I've never used anything quite this elaborate in a club or mobile setting - Only when running concert sound for large venues and that was with a DriveRack. This EV unit is similar to the DriveRack, in that it has user friendly options that can be configured for just about any room/venue. My question to Tyrone would be: Does this unit really fit your needs? It's extremely esoteric for club or mobile use. The other question is: What is the Gemini unit in the rack for? I can;t make out from the pic of the rack what the unit is or what it does.

As Balanced Line said before, a little more info is needed. If you can get a couple of close up pics of the back side of the rack as to how the outputs from the EV unit is configured into the amps (if that's how it's configured) we can give better advice.
 
Sweet processor

That unit is sweet.

A compressor, equalizer with variable Q, crossover with second or third order Bessel, Butterworth or Linkwitz filters, a limiter, delay (with temperature compensation).

If you don’t need the RS232 port you can use it to start the coffee with an external relay!
Even if I wanted to tri-amp, I’d just use a simpler external crossover for that function. Certainly some of the functions of the dx38 are esoteric but it does the bread and butter functions as well.

For the record, I had no idea what it did until you identified it sparkieg. $1288 smackeroos for that puppy.
 
That unit is sweet.

A compressor, equalizer with variable Q, crossover with second or third order Bessel, Butterworth or Linkwitz filters, a limiter, delay (with temperature compensation).

If you don’t need the RS232 port you can use it to start the coffee with an external relay!
Even if I wanted to tri-amp, I’d just use a simpler external crossover for that function. Certainly some of the functions of the dx38 are esoteric but it does the bread and butter functions as well.

For the record, I had no idea what it did until you identified it sparkieg.

I just did some searching online for EV stuff and came across the PDF files and operation manuals for that unit. Like you and I have both said, it's an extremely esoteric unit for Ty's needs. I would personally pull that unit out and go with an Ashley XR-1001 crossover. It's functional and easy to use, and can be adjusted on the fly.
 
As someone mentioned earlier in this thread, you just need to jump the inputs from your existing subwoofer amp to your added amp. The K2 has 1/4 and xlr input connectors for each channel so this should be easy to accomplish. Then get a pair of cables with banana plugs at one end and speakons at the other and hook up your new amp to the other subs.

You are out of space in your rack. When you get a new rack that will hold everything you can add the connectors for the new subs. Actually, if you intend to run that rig complete most of the time, it would simplify your setup if you used 4 conductor cables, each driving a top and sub. You could use 8 conductor cable also and only have to run a single cable to each stack, but this would involve using a breakout box at the speaker end.

I would disagree with the idea of dumping your processor to use a simple crossover. The processor can provide you with valuable tools such as limiting to protect your drivers and system processing such as peq and delays to align the cabinets. It may even already be set up for you by the previous owner.

It would be a good idea to devote some time to understanding how all of your system is hooked up and operated.
 
Yup... you may replace the OEM crossover plates with custom breakouts. There's a local guy who does this for B&B Music... he customizes OEM systems with NL8 patch panels.

Feed a tri-amped stack with one cable per side. :)
 
Why hasn't BERNIE chimed in on this?????

If the Ev is all set up for this rig, it would be VERY nice to know this.

Why spend more money on stuff you might not need???

Tyrone's gonna have a pile invested in an additional K2,plus the cableing needed for this project..

But it will totally ROCK.

Wolfie will be so proud....................................."real S/R gear"
 
Bernie hasn't logged on to this site as far as I am aware.

Real SR gear, you better believe it. I wouldn't have it any other way lol. I'd drive them dually 18s with 2500 WRMS each, Class A/B. That'd make for one helluva FOH bass system. :)