My crazy rack... Better solution?

To many ads? Support ODJT and see no ads!

LoudspeakerDJ

New DJ
Nov 16, 2006
116
0
48
I have attached a pic of my partner at a recent downtown party.

The problem.... This is a diy rack. I made this for a music only setup, and has now evolved into video. My problem is I haven't found a solution for my desktop (I didnt like any rack mounted computers, too small and limited for my liking) and monitor that swings up. Also, the wire mess below the mixer etc. is enough to make me (I like things organized) want to cry.

Is there a better solution, allowing for a desktop or especially a monitor, that still has a lid and front to protect the gear? Maybe my rack now is the best solution.

Also, it is really heavy. With the 2 qsc amps in the bottom, this thing weighs a ton. Would anyone recommend a seperate rack for the amps? I am worried about having more to set up. I like the ease of wheel this thing in and push it out, but at the same time you need to inject steroids to lift this thing into the trailer!

Any idea would be awesome. And if you want, you can make fun of my rack.

About the pic, you can see the computer half way down on its side, and that thing sticking in his pelvic region is the keyboard. Just so happened at the time the pic was taken he was messing with the lighting controller.


djrackpic.jpg
 
Well... from the looks of it I'd say the rig is ergonomically incorrect. That must be a difficult system to work with. The constant leaning forward will take a toll on the operator's back. :(

I dunno what you folks would like to do nor how much you would be willing to spend to correct the situation. All I can do is offer recommendations.

It would be my recommendation to shed the heavy wooden cases and replace them with SKB or Gator molded cases. This would solve much of your load weight issues. Split the load into two or three cases ~ processing in one, amps in another. If you work with several amps, split 'em up into smaller cases. Stack 'em, patch 'em together and hang a drape over the rack stack. We have been doing this for years with no detriment to load time. Patch cables and jacks are color coded for ease of assembly.

You can place only so many user controls in a vertical position. If you wish, you may place the lesser-used controls further down in the processing stack. If this is not feasable, look to expand horizontally by placing controls left to right. Think of a barbecue grill with shelves on both sides.

The front end rig may be installed in a separate rack case that is more user friendly. Check SKB's website for options.

I hope this helps. :)
 
Re:

Allow me to post a pic of my system so that perhaps it may give you some ideas. The amps are in the lower rack with processing equipment and the main console has the most used equipment at my fingers. I realize this doesnt solve your laptop problem, but I hope it will give you some concrete ideas that Fred mentioned in his last post.
 
Go powered so you don't have to worry about amps. That should cut the weight down greatly.
 
Just a suggestion, you can get rack mount computer cases in 2, 3, 4, 5, 6, rack space sizes, and believe me a 6 space case will have a lot more room than you need. Having that thing jutting out in front is very painful looking.

Fred has made some excellent suggestions and I will add to that.

If you are handy with the soldering iron you can put together some great connectors to go between the different rack cases to carry signal, be it "D" connector or 9 pin midi (my preference) with IEC power connectors the power situation is 1,2,3.

By breaking it all down into groups in smaller stackable rack cases you will have a much easier system to move around amd it will be a lot more versatile.
 
Just a suggestion, you can get rack mount computer cases in 2, 3, 4, 5, 6, rack space sizes, and believe me a 6 space case will have a lot more room than you need. Having that thing jutting out in front is very painful looking.

Fred has made some excellent suggestions and I will add to that.

If you are handy with the soldering iron you can put together some great connectors to go between the different rack cases to carry signal, be it "D" connector or 9 pin midi (my preference) with IEC power connectors the power situation is 1,2,3.

By breaking it all down into groups in smaller stackable rack cases you will have a much easier system to move around amd it will be a lot more versatile.


Steve, this is just the thing I am looking for. I am handy with a soldering iron, however am unsure how to make your suggestions a reality. Do you have an example of this, a pic, or perhaps more information.

i am very interested in what exactly you mean. I don't know what an iec is.

Thanks
 
is ip possible to move my computer over to a rack mount solution? The problem i found with rack systems were price, and availability for expansion. I cannot remember for sure but it seemed many of them only had 2 or 3 docks inside? Sorry i dont know the proper terminology. Mine has something like 7, and has 4 fans to keep it nice and cool. Is there a source for inexpensive rack mountable cases?

Thanks again
 
http://cgi.ebay.com/4U-19-12-Bay-US...ryZ64065QQrdZ1QQssPageNameZWD1VQQcmdZViewItem

You'll need a power supply...it takes a standard PS2 (good)..you can use the one in your case....
I bought my 19" case from here.....lots of space, lots of cooling......

how can i tell if my computer can fit inside of this one? Is it a move I can make on my own? Do i simply move everything over and hook it up like it is now? Would I need any special tools. The thing i would be worried about is for some reason mother board not fitting, or the back panel where all the outs like for video, mouse, etc not fitting the hole in this case. Are these things standard from manufacturer to manufacturer. If so, this would be a great solution. One that i am looking for.
 
Should all be standard, unless of course you have a Dell, HP or some other proprietary based pc.......there may be issues. I swapped a P4 2 gig PC - no problems....

The other option is to buy the case and have a local shop build the pc....upgrading at the same time

If you not computer savvy, I's fiond a shop or a friend to give you a hand...
 
Should all be standard, unless of course you have a Dell, HP or some other proprietary based pc.......there may be issues. I swapped a P4 2 gig PC - no problems....

The other option is to buy the case and have a local shop build the pc....upgrading at the same time

If you not computer savvy, I's fiond a shop or a friend to give you a hand...

i think ill go ahead and buy it then. My computer was built for me by a local guy. So its not a brand name. I think i should be able to move eveything over myself then.
 
Yes..you should....the plate on the back of the case (where the usb ports...etc, will pop out and go on the new case.....The front usb ports are nice as well.
You'll like the case..it's heravy though...loaded up - 40 lbs.....

Mine came with 3 fans...one large at the front , two mid ship. I bought 2 fans for the back.....

If you're unsure, you're local guy can help....
 
attachment.php


I don't get it. That's enough gear to run a small night club. Do I see a cassette player?

You do indeed see a cassette player/recorder. That's a Tascam unit that also has a triple deck CD player. I bought that unit as a redundancy/backup unit just in case the Pioneer dual unit died for some reason.

As for the amount of equipment, I'm sort of a gear head. I am very much into "clean" sound, which is why there is so much processing equipment. In the top rack/console, you will see a Lightcraft 12 channel lighting control center which has recently been uninstalled. Under that is the ETA power conditioner, then the dbx compressor unit, the dual CD controller, Tascam X-15 mixer, then on the front face, the dual CD player unit, DOD 15 channel stereo EQ, AMDJ SC8FC Lighting controller that has recently been upgraded to a Chauvet SF-9500 controller.

In the bottom amp rack, you will see an ETA power conditioner, Alesis 3630 stereo compressor/limiter/gate and under that, an ASHLEY XR-1001 active crossover unit. I decided to put the wireless mic receivers on top of the amps to clean things up a little and keep them out of my way.

And this amount of equipment is less than the amount of stuff I have seen in other's racks........
 
I just went from a laptop system (pita to set up) to a rack mountable computer dj system.

I bought it used, but it has everything pre wired inside the case with just a few "outside" connectors that need to be made. (like steve and others said)

Quick connect power, Speaker cables, and two cables from the computer case to the mixer case and I am ready to rock.

It is heavy, but saves untold time in setup. Looks so much nicer also.
 
Dan,

I also use a laptop setup (only for karaoke) and the answer to the PITA factor in setting up is a docking station. With the DS in place all the connections remain in place and you just pop the LT in place and setup is complete.
 
Steve,

That is great advice. I own an hp, and there is a sweet "expansion base" that the computer rests on, raising the screen. Plenty of usb ports, slot for a hd, etc.

I worked real well, but I still didn't like the way it "looked".

I would have bought some sort of attachment to hook up to the side of the main mixer rack, but got a hell of a deal on the rack mount system.

2 pIII's Screen, 2 60gig mains for programs, with 160 gigs for music, cases, flat screen, pcdj red, rack keyboard, mouse, mixer, controller... The works

For 1500.00. (including a nice weekend trip with the kids from Il to Ohio)!

If one does not want to go, nor has the finances for a rack. Docking stations or hp's expansion bases are definetly a great way to go!

I forgot: With mine, the usb hub needed to be powered. for some reason pcdjfx would "hicc-up" with a non powered hub.
 
I went through the break the back with my rack thing too.

Then I built a system and now use a Shuttle that carries 2Tb of storage and dropped 45 lbs at just over 70 lbs now.
I've since added a new 19" lcd that rides in a padded laptop case which also reduces weight of the monitor and power supply that is now built in.

This also allowed a lower profile instead of standing behind this towering system.
The key is adding case fans and ducts to get air flow through the unit.
Been in service doing 100% vob video over a year now without a problem or back ache.