audio component connection question...

To many ads? Support ODJT and see no ads!
Dec 3, 2006
1,618
6
51
Kansas City
I'm running two DVD players and a CD player into a 16 channel mixer which has xlr or 1/4" inputs on each channel. For best audio quality which is desirable:

1. Connecting RCA to TRS 1/4"

or

2. Connecting RCA to XLR

Thanks for any advice...
 
Doesn't matter -- just depends on your choice of connector for durability or ease. The RCAs are unbalanced.

Rick is correct I would use the XLR, better contact and no extra noises if it's pulled out by accident.
 
The correct answer is...

ProAV1.jpg

http://www.guitarcenter.com/Radial-Engineering-ProAV1-Single-Channel-Direct-Box-153934-i1124796.gc
 
The correct answer is...


Sorta like converting an MP3 to a WAV... ;)


BTW, I see no need for your average DJ to use a balanced cable. The runs are short, and if a quality cable is used, there will not be enough noise to influence anything.

Most are playing MP3s or CDs anyway, on relatively speaking noisy equipment, in a noisy environment.


Waste of money IMHO, unless you are in a studio setting, and need that extra slight extra bit of dynamics...
 
If the outputs of the DVD players and CD player are RCA, and the input on the mixer for each channel is 1/4" mono (as I would assume any Pro mixer would be), then the below would probably be a decent fix/go-between, which you can find at Parts Express at the following url:

http://www.parts-express.com/pe/showdetl.cfm?Partnumber=240-162
 

Attachments

  • Female RCA to quarter inch adapter.jpg
    Female RCA to quarter inch adapter.jpg
    23.3 KB · Views: 0
BTW, I see no need for your average DJ to use a balanced cable. The runs are short, and if a quality cable is used, there will not be enough noise to influence anything.


I wasn't considering the noise...

Did I mention that the PROAV1 is also a summing box?

JOAN CRAWFORD: "No Y connectors, EVERRRRR!"
No-Wire-Hangers.jpg



.
 
I'm no one to say either, but if you wanna play like that, you gotta pay like that.

All that projection DJ stuff wasn't cheap. Why insult it with a $2 connector?

.


Given that most DJs I've seen use those $3 RS interconnects, I'd say the $2 connector would be a match made in Heaven... ;) :)


If yer gonna upgrade one part of the signal path, you have to upgrade the ENTIRE signal path to get any noticeable improvement. I'd agree with Sparkie, that for a fixed in installation that's great -- but for a mobile rig, it's probably just spinning your wheels...
 
I'm actually connecting some very high end Tascam DVD and CD players to an Allen and Heath mixwizard for Live PA/presentation stuff...so I DO want the highest level of quality in this situation. I think I'll check out the box route but thanks for the suggestions everyone!
 
All that projection DJ stuff wasn't cheap. Why insult it with a $2 connector?

Connectors less that $2 per end are suspect due to lack of quality.
Connectors more than $5 per end are suspect due to the inclusion of snake oil.
 
After doing my research, it seems that the best and most cost effective options are:

1. There are actually two (ST1 and ST2) 1/4" inputs on the back of the mixwizard that have a single volume knob on the mixer (doesn't take up a channel space). So I could go two RCA-1/4" out of each component (DVD and CD).

2. What I plan on doing, for this gig anyway is buying some nice RCA - XLR and just dedicating two channels for each component. That way I have a nice balanced feed and can EQ as needed.
 
Hmmmmmmm, so I assume if you run this little box mono you could just run out of the left xlr output into a single channel on the mixer?

Yep, another mic level input. Designed to connect unbalanced line level devices to balanced mic level inputs on live sound consoles. We use a lot of their panel mount versions in permanent installs.

Ben