I want a mirror ball!

To many ads? Support ODJT and see no ads!
Scottie and Valerie suggest a slower motor...1mph. Are we all in agreement here? BTW, all these pics didn't come thru last night when I was looking at them but for whatever reason, they are coming thru now. They look great! Thanks all for posting them. Looks like only Fred mentioned the difficulty in positioning. No one else has anything to say about that?

--Will

Yes slow motors.
You don't want the drunks puking.
 
I really like the slow mirror ball for the slow dances. I cut the other lighting, and just run the mirror ball.

There are times when a fast turnning ball would create a good efect for some of the faster music... however I have other lighitng that also creates a great mood for the faster dances.... SO, slow is better.
 
There are so many ways...

...to mount ANYTHING. Tell us exactly what you want to do and with what you have to work with. I know we can help you do it.
 
Rasky -

What are your mounting options? That will help us suggest positioning.

Ben

FX & Tyrone, I have 2 T-Bar type light stands. I usually only use one at this point. So then, I have a vertical stand w/ a horizontal crossmember on top. The crossmember has braces connecting to the vertical stand.

Then too, I also have my mains on speaker stands, so if nothing else, I guess I can just sit them on top of one of the speakers and hope it doesn't burn up the fabric on my speakers! :sqeek:

I can make a contraption like Chuck showed, no biggie. But w/ a stand as I described, where do I mount the ball and where do I mount the spots?

--W :sqconfused:
 
Starball II ..big & heavy? huh?
I have used the same one for 7 yrs and NEVER had to change the bulb.
I set it on the table & it gives off the same effect as a mirror ball in the room.

I used to own mirrorballs, Now you want to talk about, big, heavy, always having problems with, breaking.....
 
OK, then...

If you're handy, here's a simple and clean way to accomplish what you want. Get some pipe (I use 1½ conduit from home depot, cut into 4 foot sections), or an extra section of "T" pipe from a tri-pod set up and mount the mirror ball motor to one end with two small screws.

Then use the below pictured bracket, attaching the pipe at 90 degrees from your "T" bar (or you could just as easily attach it to the upright), and mount the spot light on the other end of the pipe, shinning at the ball on the other end.

Then, just leave the motor and spot attached when you break it all down. The clamp can be purchased at any music store... it's a drum clamp.
 

Attachments

  • Right angle clamp.jpg
    Right angle clamp.jpg
    952 bytes · Views: 24
Tyrone,

Would this work

I have a t-bar stand with the extra side arms that mount to the verticle pole... if I hang a ball from the top t-bar then I could put my pin spots on the lower bar one on one end of it and the other on close to the verticle pole.. with the ball centered between them...

then I could hang something else on the other side arm to balance out the stand... what is the weight of your 12" ball with mounting? I have a Vue III which is 12lbs so I worry that I might be over balanced on one side vs the other.
 
Starball II ..big & heavy? huh?
I have used the same one for 7 yrs and NEVER had to change the bulb.
I set it on the table & it gives off the same effect as a mirror ball in the room.

I used to own mirrorballs, Now you want to talk about, big, heavy, always having problems with, breaking.....

Yo Bill! This was part of my original question! Besides all the positives I'm reading (which are great), I'm also wondering about the negatives of a mirror ball, which is why I bought the StarBall in the first place. I thought a mirror ball would be too much bother. But I'm just not so pleased w/ the StarBall...which is why I'm reconsidering a mirror ball.

So I welcome the negatives too, Folks.

So, Bill, besides being big and heavy and breakable, what else? Difficult to get the beams just right? :sqconfused: