So you'd like to build a professional PA system...

To many ads? Support ODJT and see no ads!
Tyrone, you have pretty much everything you need except for a mixer. Like it's been said, you'll need lots of channels (16 would suffice, 24 would be better). Use some of your smaller speakers and amps as monitors and you're good to go.

BTW, I know many bar bands that would kill to have a setup like that JBL rig.
 
Tyrone Blue;89182So let's pretend... Let's say that I have a few guys on stage that use up 8 channels (guitars said:
Yes.

Yes.

and yes, you have the right idea on the speaker outs. We use multi wire speaker cables so we can run 1 cable to the first highpack of each side...1 left and 1 right....then jumper from cabinet to cabinet. Jumpers are cheaper than 60' speaker cords. It is still using multiple amp channels, but eliminates the need for those 12 speaker jacks up top which is normally not practical.
 
Hit the road...

Precision, you're welcome any time... In fact, anyone is welcome any time... I have a guest room.

Is the crossover what you are calling a "processor"?

This system needs to be working by this time next year, so I have time to learn and get it ready for the new nite club. I'm not "planning" on letting bands use it, so I don't have to necessarily have the ability for a big band, but just in case, I'd like to know what I'm doing if they want a system... or for rent.

In the mean time, I'd like to have something more than my little DJ mixer with RCA inputs. Someone should write a simple to understand book.
 
Although I learned most of my sound engineering work through my old job, and working with the local IATSE union, I learned the right techniques of sound engineering... With that said, I still have learned plenty of things at this other board I lurk at... http://www.prosoundweb.com
 
Precision, you're welcome any time... In fact, anyone is welcome any time... I have a guest room.

Is the crossover what you are calling a "processor"?


Yes.




I'm not "planning" on letting bands use it, so I don't have to necessarily have the ability for a big band, but just in case, I'd like to know what I'm doing if they want a system... or for rent.




I would be very careful who you "rent" this powerful rig to.

Reconing those JBL'S will be very Expen$ive...


And Valere,
I figured you were aware that this was Bernie's 'ol P.A.
But was just checking.
 
Where's Brian B when you need him? :D

Seriously, Ty... an active crossover is technically a processing unit. With the system you have, you'll do well to bi-or tri-amp it with the crossover. It's gonna make a lot of noise and somebody's probably gonna call the cops (personal experience) but the overall tone is so amazing that you'll never go back to full range speaker systems. :)

Large soundboards are indeed a requirement for working with bands that have to be miced or DI'ed (direct input). It's not that big a deal if they're working a small bar or something. They can usually work with a powerhead and pair of full range cabs on sticks. If they need more output, they may patch the powerhead line out to your FOH system.

DJ mixers are fine for DJ shows. KJ mixers are a must for karaoke hosting.

The big FOH systems and big soundboards are more for large venues and outdoor shows where everything goes through the soundboard and is returned to the amp racks.

Running live sound is a whole 'nother animal altogether. You will need monitors ~ stage wedges or in-ear. Bear in mind that stage wedge monitors are designed specifically to be directional. If you need wedges, get 'em. Don't try to substitute PA cabinets for stage mons.

You will also find it necessary to employ gates, limiting and compression. Some performers are just plain picky... and they won't be very impressed with inexpensive Nady mics. Some lead guitars are hard of hearing... and they'll be screaming for "more ME in this monitor!"

The soundman's job is never easy. :)
 
Just for everyone's info - Tyrone's BIG RIG speakers are exactly the same as what we are using in The RED ROOSTER. We fly the mains from the rafters - 2 on each side of the stage. The subs are 4-ohm, 3200 watt (peak) bass monsters. These things will rattle your teeth and make you think your heart's gonna jump outta your chest. 'Course, we have the sub cab's inset in the stage front, so the underneath area of the stage acts like a huge resonating baffle, which re-enforces the low frequencies. The Rooster is a 10,000 square foot facility and this system is EXTREMELY loud even when the club is full of patrons.

Basically what I am saying is that with the right combination and number of amps pushing that system of Ty's, it's enough to raise the roof on just about any club venue.

Now, for some basic advice on mic'ing certain instruments:

The drums will require more than just one microphone to sound right. As was said earlier - you have to mic the kick drum, the snares, the tom, the high hat cymbals, etc.

The guitar amps normally have one mic each. If there are vocalists, they probably have a mic each.

Let's assume the following:

4 man band and each sings.

(4) vocal mics

1 mic each for the guitars -
(1) mic for the lead guitar amp
(1) mic for the rythym guitar amp
(1) mic for the bass guitar amp

Lets assume the drum kit consists of the folowing:
1 kick drum
2 snares
1 tom
1 high hat cymbal
2 sets cymbals

Thats a total of 7 mics for the drums alone.

Now we're up to 14 mics already. Each would require a channel on the board to be mixed correctly. I hope this is basic enough to understand.

The crossover is somewhat of a processor. It's more of a glorified EQ. It splits up the certain frequencies and sends them to the various amps. Ty's EV unit is a combined EQ/Crossover/Compressor/Limiter. We have two of these units in the mains amp rack at the new club I am spinning at.

I will add more to this thread as thoughts pop into my brain.
 
I'm slowly catching the drift...

OK, lets back up for a moment. I'm beginning to see that a full 32 or even 16 channel PA isn't what I want or need.

The band I was commenting on earlier got away with the "box" style mixer pictured at left above, and it sounded pretty good (I believe it was only 8 channels, and the drums just went live with one mic). I'm now thinking that that is all I really need or want. I also think that 8 channels is enough for my needs (but could do duty for a small band in an "emergency").

So lets concentrate on that concept. I'm not sure what the unit on the left is called, but I'm referring to it as a PA mixer (is this correct?). Fred, what's a "power-head" (is it the same thing)?

So, if I take the output of my computer, and cable that (with an isolator transformer in order to get XLR outs) to feed into the "PA mixer", then take the output of the PA mixer, and feed it into my amp rack, will that work? I assume it will, but is this the correct way to use this PA mixer in my system?

Then, assuming that there is more than one set of outputs on the PA mixer (is there?), can I run active speakers from these outputs as well as passive outputs to the amp rack (thus combining active and passive speakers)?

This is enough questions for this session...
 
Oh... one (or two or three) quick question(s)...

I always see a microphone set up in front of a smaller guitar speaker on stage. Is this because the microphone is picking up the sound from the guitar amp, and feeding it to the mixer, rather than the guitar having it's own input to the mixer? If so, is this a cheap way to do that, or is it the best way to do that?

And, I was looking at mixers on e-bay last night, and the Mackie mixer I looked at had all of the inputs listed as "mic". Does this mean that only microphone can be inputted here, or can any device with an XLR cable be put in here?

Then, is there a major difference with "inputs" and "outputs" being XLR verses ¼ phono plugs?

Get ready, I have a lot more of this type of question.
 
I always see a microphone set up in front of a smaller guitar speaker on stage. Is this because the microphone is picking up the sound from the guitar amp, and feeding it to the mixer, rather than the guitar having it's own input to the mixer? If so, is this a cheap way to do that, or is it the best way to do that?.

I'm glad to see that you are catching on. Now to answer this first question:

Yes, the output of the guitar's amp is what the mic is picking up and sending to the mixing board. And yes, this is the way I have always done it.

And, I was looking at mixers on e-bay last night, and the Mackie mixer I looked at had all of the inputs listed as "mic". Does this mean that only microphone's can be inputted here, or can any device with an XLR cable be put in here?

The XLR inputs on the Mackie powered mixer you saw on e-Bay are Hi-Z inputs. The reason they are listed as "mic" inputs is because that's what is recommended by the factory. I personally don't recommend using anything other than a microphone in these inputs due to the internal electronic characteristics of the mixer. The XLR inputs are designed with certain frequencies in mind. This is why you will see certain mixers that list the inputs as both Hi-Z and Low-Z.

The band I was commenting on earlier got away with the "box" style mixer and it sounded pretty good (I believe it was only 8 channels, and the drums just went live with one mic).

While mic'ing the drums with only one mic will suffice in very very small venues, it isn't recommended for larger halls or venues.

I'm not sure what the unit on the left is called, but I'm referring to it as a PA mixer (is this correct?)

I am going to assume that the mixer you are referring to is the Crate unit. This is a POWERED MIXER, which means it has it's own internal amplifiers - probably 2 individual amps rated at somewhere around 200 watts per channel or higher. If you are going to mic the band, DO NOT USE THIS THEN SEND THE AMPLIFIED SIGNALS TO YOUR AMPS! You will fry the K-2's in the process.

You want to use a non-powered mixer for mic'ing the band.

Let's assume that the 8 channel board that has the wood-grain cabinet in the picture is non-powered.

You would want to use this to mix the different mic'd instruments and the lead singers (if there are any) on stage. Since we have not discussed the use of stage monitors in this set-up let's assume there aren't any. I would have at the very least, a pair of headphones that you can hook into the headphone jack on the mixer so that you can listen to the mix in your head. Send the signal output from this mixer to the EV unit in your rack, and from there you can "sweeten" the sound using the various processing devices prior to sending the mix to your amps.

So, if I take the output of my computer, and cable that (with an isolator transformer in order to get XLR outs) to feed into the "PA mixer", then take the output of the PA mixer, and feed it into my amp rack, will that work? I assume it will, but is this the correct way to use this PA mixer in my system?

Before you use one of the XLR inputs on the board, look for a "TAPE" input. This will be an RCA input connection on the back of the board. This will allow you to free up one of the much needed XLR inputs. You can usually mix the output of (in your case, a laptop) whatever is feeding this input on the board with the rest of the inputs. I use to do this all the time at church when we had to do a special slide show presentation.

So, if I take the output of my computer, and cable that (with an isolator transformer in order to get XLR outs) to feed into the "PA mixer", then take the output of the PA mixer, and feed it into my amp rack, will that work? I assume it will, but is this the correct way to use this PA mixer in my system?

Then, assuming that there is more than one set of outputs on the PA mixer (is there?), can I run active speakers from these outputs as well as passive outputs to the amp rack (thus combining active and passive speakers)

In theory, combining active and passive speakers in this configuration might work, but I would be concerned about the high frequency time alignment sounding weird.
 
What I hear you saying...

...is never use a powered mixer's output and feed it into an amp rack? Therefore, I guess I need an un-powered mixer...right?

I already have a isolator transformer, which I'm using with my active system right now, so I know that will put out a signal via XLR. I also understand the "tape" input being used with my computer.

So, I am now thinking that I need an un-powered mixer with at least one RCA tape input (I think that's what Jay said way back in the beginning). Then, anything else that I'd want to feed through, should have a microphone sitting in front of the sound source, and I'm good to go.

Then, if it's an un-powered mixer, couldn't I use an extra output to feed to active speakers (like a "tape out")? I read your explanation but wonder it anyone does both systems this way?
 
BEN... are you listening???

I'm on my way up to see Ben tomorrow and pick up two Eon G-2's. I might try to swing a mixer on this deal too.
 
Sending an amplified signal can and WILL cause permanent damage to the amplifiers parts, and may void your warranty. The big boy's you will find will NOT couple the amp into the mixer, it just isn't rider friendly. (To find out if your outputs are amplified or line level, read the manual or look on the board, you may see, balanced, unbalanced, for unpowered; and xyz watts at X ohms)

If your considering getting a pro audio system get something that is rider friendly, as in big bands will put this on the list of acceptable equipment, Not to be a stab, but you will not find Carvin, Peavey, Mackie, RCF, Nady, Radio Shack speakers that are rider friendly. Of all the riders I have seen for bigger bands. Recommended brands for pro audio include, JBL (Certain Models), EAW, D&B. Mixers are typically Yamaha, Crest, Soundcraft... Don't forget connectors... I never have seen too many "monster" cable. I really don't think those cables are worth the extra cost... I find that connectors need to be Neutrik, cable is typically Belden or Canare, ETC.

Keep all that in mind when building your system, not only will it help you make money, and your investment worthwhile, but will help your system hold its value much longer and give you a better resale value, finally your fellow audio peeps will think much more highly of you :)
 
Travis,

I beg to differ on the mention of Carvin equipment not being rider-friendly. The Carvin name may not be on "the list" but the DCM amps (Class A/B, Toroid power supplies), the TCS line and SL consoles are definately up there with the established touring grade brand names.

It took Carvin a few years to figure it out but they finally got it. :)

Ty, a powerhead is just another term for a box mixer.

As far as micing guitar amps (or halfstacks) on stage, this is preferrable for a few reasons. One, many guitarists prefer the tone from their own systems (many use tube amps and exotic speakers). Two, if you mic it, you've got their tone out to the audience without stage sound wars. Three, guitar amps aren't designed to fill a house anyhow.

On a side note, I saw Marty Stuart in concert at the Nissan Pavilion back when he was still touring. The band had their regular musician stacks on stage. Everything was miced to the house system. And they rocked. :)

XLR patching has one advantage over 1/4" TRS (tip, ring, sleeve) ~ the TRS contacts in the jacks and plugs can become tarnished over time and may need periodic cleaning. XLR connections don't seem to have this problem.

I hope it helps. :)
 
I did it...

Richie, myself,and Marie flew up to Bemidji this morning and picked up all sorts of equipment from NorthernLightFX. Pictures soon...

I bought two 15" Eon G-2's (and bags) and a Soundcraft EPM12DJ mixer, along with some extra accessories. I'm now ready to do live sound for a band if the need arises.

Ben showed me several ways to feed all of my sound gear into the board, and get it out of my big speakers... YIPEEEE! All I really need now are some quality microphones.

I also got a stage snake to connect everything. Going to fire up the whole system this weekend and I'll do a video for YouTube.

For those of you who noticed "Kat" on the board yesterday... (she's the brains of NorthernLightFX), be sure to welcome her on the board, and say hello.


Ben's going to make me pay for that "brains" comment.
 
Pictures...

I posted pics in "the Light Shack" from this morning's trip to pick up gear.
 
Glad to see you recieved some good help Tyrone!

It should really be an eye-opener when you get it bumpin' in the garage for the first time....

Your DJ rig will never be the same..............................

Enjoy!
 
... All I really need now are some quality microphones.
Carvin offers those, too. Not the wireless stuff. The corded vocal and drum mics are nice from what I understand. The M68 vocal mic is a great unit. We've been using one for years. :)

End shameless plug, lol. :D
 
I think if you look close you will find that alot of Peavey equipment is rider friendly also. There are several bands that use Peavey exclusivly