Should I get an EQ?

To many ads? Support ODJT and see no ads!

DJ JohnThe1

Mac Daddy DJ
Aug 12, 2006
6,832
1,699
126
NY born and raised. Living in NJ.
Here is the reason why I ask. My Yorkville powered tops simply sound so much better than my RCF's with out a sub. The low end sounds nice and deep. I don't get the same type of response from my RCF's.
I guess since the Yorkvilles are powered the amp inside has it's own processing. If I added an eq to the RCF system will it give me better bass response?
 
Well... an EQ is a necessity with passive systems, I believe. You're correct in that active systems contain their own processing. Many if not most are bi-amped. The internal processing is tailor-made for the system. That's why they sound so nice. :)

As to an EQ enhancing lower or mid-lower response, that's a possibility. The best use for an EQ is to ring out feedback and shape your tone to the speaker systems you're using. They're especially nice when you're doing live sound. When set correctly, they can enhance frequency bands by cutting others.

There's the ticket to successful EQing ~ cut, not boost. If you desire more bass warmth, try cutting the mid and high responses a bit first. These frequency bands may simply be competing with the lows and overriding them.

I hope this helps. Let us know what you decide.
 
Well... an EQ is a necessity with passive systems, I believe. You're correct in that active systems contain their own processing. Many if not most are bi-amped. The internal processing is tailor-made for the system. That's why they sound so nice. :)

As to an EQ enhancing lower or mid-lower response, that's a possibility. The best use for an EQ is to ring out feedback and shape your tone to the speaker systems you're using. They're especially nice when you're doing live sound. When set correctly, they can enhance frequency bands by cutting others.

There's the ticket to successful EQing ~ cut, not boost. If you desire more bass warmth, try cutting the mid and high responses a bit first. These frequency bands may simply be competing with the lows and overriding them.

I hope this helps. Let us know what you decide.


I agree with Fred but then again I dont run powered systems either. If it was me I would rent one to see if it would help out before buying
 
Another thing, when boosting low frequencies with the equalizer on a powered system, you can clip the amp sooner and the speaker could go into thermal protect mode.

As Fred has mentioned equalizers should be used more as a way to cut back instead of boosting the signal.
 
Dude are you growing Senile??

Well... an EQ is a necessity with passive systems, I believe. You're correct in that active systems contain their own processing. Many if not most are bi-amped. The internal processing is tailor-made for the system. That's why they sound so nice. :)
FRED YOU MIGHT WANT TO HAVE THAT CHECKED.............
As to an EQ enhancing lower or mid-lower response, that's a possibility. The best use for an EQ is to ring out feedback and shape your tone to the speaker systems you're using. They're especially nice when you're doing live sound. When set correctly, they can enhance frequency bands by cutting others.

There's the ticket to successful EQing ~ cut, not boost. If you desire more bass warmth, try cutting the mid and high responses a bit first. These frequency bands may simply be competing with the lows and overriding them.

I hope this helps. Let us know what you decide.
Heres hoping you arent coming down with something Fred its too unlike you to compliment those plastic piles of Chit.

Thanks for finally coming out and admitting it.:sqwink:
 
Plastic is for toys.

Thanks, Jon. :)

Silly me... I neglected to mention that Carvin's LS series (poplar plywood & rat fur) is available in active versions. ;)
 
DBX Driverack....

You can configure how you want. But you can have independent EQ for each pair of outs.....

The outs are labeled Low, Middle, High and left/right on each, but you can configure how you want. IF you like the Yorkies as is, leave the EQ flat.

Then you have....
Feedback suppression
Limiting
Compression
Parametric and Graphic EQ
Crossover

etc.