DMX setup up and running..

To many ads? Support ODJT and see no ads!

Rockinct32

New DJ
Oct 25, 2006
38
0
39
couldnt wait any longer and went and grabbed an Elation DMX Operator.. Very simple controller, 12 fixtures, 240 scenes, 6 chases... any who plug everything in, get the addresses down, got my martin light working like a champ, even taught myself how to save scenes and put them into a chase, and got the chase working!! did all of this in about an hours time. not bad for a newbie.. anyways I am having one problem. My elation protron star strobe is continually blinking every 10 seconds, when the fixture is not selected, and if it is, all the values are 0. Not sure why this is. I had it set to address 1 and 7 and 8 just to see if that had an effect on it, and changed how it was wired in the chain, but still the same thing. I had to order that end of chain terminator plug, but I cant imagine that being the problem. Of course I dont want this thing on all the time. It cant be blinking when I have a slow song playing. What could I possible be doing wrong?
Josh
 
I've had a simular experience...

If this is the problem, it's very easy to fix.

You need to select the strobe, on which ever scanner button you have it set up on. Then, bring all of your channel sliders all the way up and then all the way down while in "program" mode. That shuts down the signal. It's just that simple.

The reason this works is, when you have a channel set, the controller keeps that signal defaulted where ever you last had it set to, until you move the sliders to change the transmitted signal to that fixture. I have this happen all the time when switching scanner buttons, and it's easy to forget.
 
tyrone, i'll give you credit for that reply, but I seriously had the same thing, revised my reply though to make it simpler first, i didn't want to give out inacurate information about the operator. I think they have a bank/page switch, click the button and up and down your sliders as TB said.
 
ok i will have to try it tomm afternoon when i get it all setup again... i cant wait to get some scanners involved in this now. I am just using my strobe and martin efx600, the only two dmx lights ive got now..
josh
 
Another question for you. The chases, you can only run one of them at a time correct? I am trying to figure out how to setup a chase using multiplie lights, but running them at the same time. So not to have one light doing one thing at a time. I am only working with my EFX600 and strobe, so this is kind of more difficult to understand. I know how to insert scenes into a chase from one light, but not sure how to do it for a second light?
Correct me if I am wrong, but my chases are going to be used for; 1 chase for a slow song, a couple chases for some fast songs, maybe a few custom chases to a certain song. That is what it is for correct?
 
The newer controllers...

...like the DMX 55, allows multiple chases at the same time.

Remember in a chase, you have 240 "steps" allowing you to program any scene as many times as you want (up to 240). Set up your scenes to give the look you want in one chase, then, switch to another chase if you need to.

Or, buy one of the newer controllers that lets you run more than one chase.
 
do the chases run the scense in order you put them in? or do they just play whatever whenever randomly?
 
Chases...

They run in the order you enter them. You can enter any scene in any bank, and come back to it at any time, or as many times as you want.
 
Ok now this might be a problem with not having that line end terminator yet... when i run through bank 1 scenes, only ones i programmed with the strobe, my efx600 comes on, no matter which one i press, the same thing. i dont think it is a scene i programed, but it possible could be.
second problem, the damn strobe still wants to blink continuously but randomly when no scenes with it are running. i did do the program thing and set it all to 0, and that seems to wrok until i do something else.
next question, how do you black out one light, and keep the rest running? say i only want my marting light going SLOW for a slow song, so no strobe, UV's which will be on a dimmer pack, or scanners or moving heads. do i just make scene 1 for each light to be blacked out? i am still unsure of how this all works together to make an entire show that i can controll very easily.
I want to be able to have my scanners and such run on chases which i know how to do now. and than be able to make a scene for the strobe to do one effect, just pop on, do the effect, and than turn it off, but keep the rest of the chase keeping on going. the same with the uv's. They are goiing to be on a Switched DMX control pack, so a few songs they will b on with the chases going, the next few songs turn em off, but keep the chases going all the smae. I am going to have JTNichol on here come over and teach me some more once i get some more scanners or something. Im thinkin my strobe is just being tempermental and might be going back.
josh
 
Josh, I doubt you will need a terminator, for our runs we haven't ever needed to use one. I attribute that to good quality cables, or just luck. However, I have heard if you are having no problems then use a terminator you can cause more trouble :$

To me the trouble seems to me to lie with the controller. I hate to say check the manual? Bounce now ducks waiting for a WhopA** can to hit me. Dang Chris stop playing games in the arcade!
 
See me chuckling???

Your first post said you had it all working and it was "simple". I'm confused with that comment now... not so simple???

Well, I suspect you may be using a controller that someone else owned before you. It sounds like you have scenes already in it from previous programming. You need to delete all of your scenes and banks and start over. Your manual will tell you how to do this.

If that isn't the issue, then you have your addresses set wrong or you are punching the wrong scanner buttons. Sounds like you need some DMX instruction.
 
OK I will try to make this a bit easier. Sorri about the confusion. My strobe has dipswitches, since it has these I figure I would make it easier on myself and set its address to 1. Very easy. To make it even easier for me, i use that as my first light in the daisy chain. The second light, the martin EFX600, is set at address 17, and is the second light in the daisy chain.

Now I don't think this was an open box unit, because all of the plastic and the power pack were all nicely taped up and neatly organized, but I am going to delete all the scenes again just to make sure.

Now when NO chase is on, and the audio trigger or Auto trigger is off, i can select either light and do what I want with it. But regardless if the strobe is selected or not, it continously blinks at a very slow pace, maybe every 15 seconds. NO matter how many times I select it and set everything to 0, it still wants to blink. I thought maybe the polarity selector on the controller might affect that, and than I found out it doesn't have one even though the manual says it does (need to look into that a little bit more). So thats what I have figure out so far. Let me know if I left anything out, as in important information

Thanx for all the help so far,
Josh
 
OK... then, go back...

...to my statement about the channel sliders. Select your strobe ( scanner button #1) while in "program mode". Check to make sure you only dip switch number one turned on (on your strobe), AND (very big "AND"), make sure you don't have a "special" dip switch on the strobe that allows for stand alone (this might be a tenth dip switch).

You have to be sure that your strobe is set up for DMX triggers only. Check your manual first for "DMX mode" triggering, and make sure you don't have it set to "sound active". In fact, tell me how many dip switches you have on this strobe, and what brand it is. If you have ten dip switches, then that's your problem. Make sure the strobe is in DMX mode (turn on switch #10).

While in program mode, and selecting the strobe, slide all of the channel sliders all the way up, then, all the way down. You MUST do this in every scene that you have the strobe programmed into. You have to "shut off" every scene in that bank. Do it 8 times. In other words, select each one of the 8 scenes (one at a time) and slide up and down... 8 times. This will shut off all signals to the fixture. If this doesn't solve the problem, then you have something else wrong.
 
Sounds like data collisions....I remedied this in my setup with a terminator....
thoughts anyone?

Yes, I also agree with using GOOD cables.
Tyrone is on the money with the whole programming mode delimma. Read that over and over....I've done that too...

Hey rockin....can I borrow your Elation Power Spots for my music concert on Wed/thurs? I'll need em Tuesday for programming and bring your strobe! I'll test it all on my rig!
 
I dont have em yet JT, I haven't ordered any more gear that just my lights so far. Its sometime in the near future, a week or so, just haven't got the funds in my account yet to start dipping into them yet. You will be the first to know, don't worri...
Josh
 
Awesome, thanks Ty, that did work. Now I have all my strobes in bank 2 scenes 1-6. Now when I go to bank 1 and hit scene 1 it starts to strobe very slow, I think i might have programmed this in the beginning by accident. I am going to fool around some more, and than delete everything and start over and that should solve my problem.
Back to one of my other questions I dont think i got answered, if I only wanted my scanners or only my strobe on at one point in time, what would I have to do to accomplish this? basically everything else blacked out?
Would i just set my number 1 scene to basically blackout, and than keep whatever I want else on, ON. I am not sure in what sceneario I would want this, but... I am just thinking for ahead.. like basically strobe, UV's, and maybe one set of my scanners off for a slow song, so I would have my moving heads on, with my martin efx600 scrolling very slow, and than everything else off....

Next question, when you see demo's of lights, or see what other people can do with these lights, how do they get their lights to "dance" with the music. For instance, i think i already mentioned this, setting up a chase to DARUDE Sandstorm. Is it possible and is it worth the time and effort?
Josh
 
You can make your lights...

...do anything you want, and at any speed. The key is proper programming. I'm going to say it's not as simple as your very first statement might lead others to believe.

Go to Best Buy and get yourself a DVD titled "Pink Floyd Pulse" and watch the programming of those lights (almost 300 Intel's dance to the music). Amazing skills shown there and this was filmed back in 1994 when DMX was brand new.

I think you need some intense DMX instructions... I hear there is a guy somewhere here on the boards who is selling a DMX for beginners book. Ask around.

BTW... always program 8 scenes at a time (fill up that bank). When you go to "auto" mode and select that bank, you'll have two dead spots with only 6 scenes programmed. It looks bad when running the show.

You can run your strobe in "static" mode by making sure your "music" and "auto" buttons are off. Then just hit the scene button to flash the strobe the way you programmed it. Change the way it looks, buy hitting another scene button... and so on...
 
Ok yea I know what you are saying about those scense. And I was playing around with the fade time and speed and I understand how that works, makes perfect sense. I do agree I might not some instructions still, but this is making complete more sense. I jsut need more lights and more time to get my fingers dirty. The best way I learn is to do it, make mistakes, and learn from it, not always reading, boring!! lol But thank you for the advice, and I will have to see if I can get my hands on that DVD im sure it was one pretty bad ass light show..
take care
josh
 
Now I'm laughing...

OK, don't read the instruction book, and play. It took me almost a year of playing to learn the controller. The book speeds that up to about two days... your choice.

In any event, once you have DMX figured out, you'll never want to go back to analog. Kinda like riding a Harley... nothing else measures up.