Config the rack today

To many ads? Support ODJT and see no ads!

rickryan.com

Mac Daddy DJ
ODJT Supporter
Dec 9, 2009
20,055
18,457
62
Hendersonville, TN
www.rickryan.com
Just got everything re-configured and working. I have the day off and we have friends coming over for a little pool/movie party. I setup my main rig in the garage and will drop a projector out by the pool. Thinking Iron Man or Thor and see if we can annoy the neighbors a bit this evening.

I re-loaded my rack. Put the Carvin DCM3800x for subs (1100 watts per cab, 4-ohm), Peavey IPR3000 for tops (440 watts per cab, 8 ohms), dbx Driverack PA+ for crossover and playing with the settings on it now but obviously, haven't cranked it yet to really hear it. I like the menus and already have limit, tops compressed overeasy, 45hz shelf, 125hz crossover point. The only negative I see right now on the driverack is they have 4 mute buttons on the front that could be bumped but even then, they're pretty well out of the way and I doubt will ever be touched. I guess they could come in handy for any kind of emergency/failure. I still have a Beta55 Elvis mic (wired) and have switched out my Sennheiser for the GTD 2-channel. I have to say it, the GTD is a better unit. Capsule sounds better, better feedback rejection, and the on/off/mute switch is where everybody expects it. Can't tell you how many times I've had to stop a toaster from dinking with that stupid little red button on the end of the sennheiser. It was a poor design choice. Here are some pics.

IMG_20130817_114435_759.jpg
IMG_20130817_114446_644.jpg
 
Rick .. why don't you split the amps from the rest of the components? Use a 10x2 or 10x4 for the mixer/laptop/mics and a separate 6U or 8U box for the amps. That way you can place the amp box out of the way for some events or stack the 2 (assuming you get matching dimensions). The alternative would be to get a larger unit with casters. I had a mid size setup like yours and found it chunky (heavy and just the wrong size). Went to a split setup and can now bring the amps if needed (my Yorkville rig) or not (my active speakers). Everything else stays the same.

Also, I would set up the wireless mic antennas away from the laptop lid, as that is usually where its WiFi antennas are. At some point, if you need WiFi access, you may get issues.
 
Last edited:
  • Like
Reactions: 1 person
Your rack will look much better with either a Laptop Stand or Swing Arm that allows your laptop to be mounted over the equipment rather than on top of it. I have both but both mainly use the swing arm. http://www.youtube.com/watch?v=chViYnuC5Ok I modified mine to be mounted Vertically on the back of the Rack Case. If you need pics I will be happy to send or post. The Odyssey Laptop Stand that I have can also be mounted vertically You have to remove the bottom plate and use the Clamps to secure it vertically to the case. http://www.odysseygear.com/odyssey-...-blue-mobile-dj-laptop-stand-with-clamps.html

As I mentioned, I prefer the swing arm as it can be tilted and lifted in any direction. You will have access to anything mounted below it.

- - - Updated - - -

Here is another good option for a Laptop Stand that can fit over your rack. http://compare.ebay.com/like/380694216420?var=lv&ltyp=AllFixedPriceItemTypes&var=sbar
 
Last edited:
  • Like
Reactions: 1 person
Your rack will look much better with either a Laptop Stand or Swing Arm that allows your laptop to be mounted over the equipment rather than on top of it. I have both both mainly use the swing arm. http://www.youtube.com/watch?v=chViYnuC5Ok I modify mine to be mounted Vertically on the back of the Rack Case. If you need pics I will be happy to send or post. The Odyssey Laptop Stand that I have can also be used vertically You have to remove the bottom plate and use the Clamps to secure it vertically to the case. http://www.odysseygear.com/odyssey-...-blue-mobile-dj-laptop-stand-with-clamps.html

As I mentioned, I prefer the swing arm as it can be tilted and lifted in any direction. You will have access to anything mounted below it.

- - - Updated - - -

Here is another good option for a Laptop Stand that can fit over your rack. http://compare.ebay.com/like/380694216420?var=lv&ltyp=AllFixedPriceItemTypes&var=sbar

I disagree on the look. I prefer it this way. Thanks.
 
  • Like
Reactions: 2 people
Wow, just finished up with the movie. That driverack is fantastic. Used a crank stand to push one of the tops about 9 ft in the air and dropped a 50ft vga cable to shoot projector, poolside. First time we've done that at this house. Around the pool, I have ISL strung and put it on, dimmed. I'm really interested to hear this driverack on a gig next week. It was super-smooth to work with.
 
I finally got around to buying the rta mic for mine and it made a huge difference in sound at my last gig. If you don't already have the rta mic spend the $99, its worth it.

Already been eyeing that. Do you just stick it into the unit or run a cord to go external? Do you re-shoot every room?
 
Already been eyeing that. Do you just stick it into the unit or run a cord to go external? Do you re-shoot every room?
Yes you do. Each room Venue is different. You can save the settings for each venue if you are going to setup in the same place using the same equipment. You can even go as far as resetting once people are in the room as that can alter the acoustics..
 
  • Like
Reactions: 1 person
I use the Behringer ECM8000 measurement mic with my DriveRack PA .. works fine. The dbx mic is probably a little more rugged, but the Behringer is flat enough from 50-18000 Hz.

I have shot 2 rooms, and while you can get a better frequency balance, most of the issues in large rooms are reverberation and reflection related and the analysis can't do much there (except maybe notch out a few offending frequencies). So if you use it, you will still need to fiddle with placement, gains and so forth .. and if you use the feedback reduction (which works great), reset the filters every so often after someone speaks so you don't compound the notching. After I set up the system, I will normally leave the unit on the feedback reduction page and then its a two button push to reset the dynamic filters.
 
Already been eyeing that. Do you just stick it into the unit or run a cord to go external? Do you re-shoot every room?

Get a long mic cable to run out to where you want your sweet spot to be and yes I re-shoot every room since every room is different. The wizard only plays the white noise for a short time so its not a long process. It takes longer putting the mic on a stand and running the cable to the driverack than it does to run the wizard. Make sure you sign up to the dbx forums, they have different methods and tips.
 
  • Like
Reactions: 1 person