How To Maximise Gain

To many ads? Support ODJT and see no ads!

Mr. K

New DJ
Aug 7, 2006
4,215
0
Please, could we devote this thread to EXPERTISE, directed to MAXIMISING our sound? (ie: input/output levels on our mixers and amplifiers)

**inspired by a Mackie thread**

Post away.

Thanks.
 
Entire books

While entire books have been written on the topic or really topics involved, that is the general purpose of the Gear Head forum.

Vinyl, might you have a specific topic not quite so all-embracing in mind?

If you are speaking specifically to setting system gain structure, an excellent article on the subject may be found on the Rane site:

http://www.rane.com/note135.html

The article is fairly technical so that might be the start point and if there are any questions, come on back!
 
Your Post In The Mackies Thread

All unity gain signifies is a gain of 1. A signal equal to what is coming in the input is going out the output. There is no universally accepted standard for unity gain. Was that a balanced or unbalanced line level signal? Most signal processors have a built in gain of 6db (there are exceptions) but these devices are generally viewed as possessing unity gain (line level in, line level out).

The positions of the input sensitivity controls on amps are set relative to what comes before and goes after. There is no absolute correct setting except in the scheme of the entire system. The escutcheon on the power amp volume control (this includes powered speakers) is there as a general reference not as any hard and fast rule.


You clarified everything for me.
 
Well OK then.

Damn, that was easy!
 
LOL.......

The only real concern in gain structure is having each piece in the chain to reach to same level at the same time so there is no clipping occuring in any part of the chain.

Having your mixer clipping because a processor gain is set to low and you are trying to reach a useable volume is just as bad as having an amp clipping because the olny thing you are looking at is the meter on the mxer (which is still reading low) because of unity on the mixer being 1.4 volts and the amp unity being .75 volts.

Just trying to confuse him again ;>)
 
Success

Just trying to confuse him again ;>)

Congratulations.

//

Considering that there is no "ONE RIGHT" way, I guess the important thing to note is to try to NOT do anything the WRONG way, which is determined by the fact that you've just blown your speakers or something.

//

I was really hoping that we could create a "universal" step-by-step guide, or something, but it is just as important to realise that there ISN'T a "universal" step-by-step guide (at least, not for dummies--like me :().
 
Actually it is pretty easy and when I have more time I will post on the subject in a way that is easy to understand.

All you need to do is check to see what the unity gain input and output is for all your inline gear. Then make adjustments where they are needed to balance that out as much as possible so when one piece goes hot all pieces in that line go hot at the same time.
 
Well Yeah

Not too high so that you clip the signal in any stage nor too low that you might fall into the grass.

If the signal is too high you can clip. If it is too low you don't take advantage of the maximum signal to noise ratio the equipment can produce. The "grass" sounds just like grass in a gentle breeze. It looks like grass on an oscilloscope too!

The right signal level is just like "baby" bear of The Three Bears, just right.

The Rane article is very good and I do recommend it if anyone wants more detail. Steve, you might want to read it too as it is so good you might just want to simplify it rather than re-inventing the wheel.
 
You Can Start Here

All you need to do is check to see what the unity gain input and output is for all your inline gear.

I don't even know what that means--only sorta, thanks to that article.

:(

OK. How's this for a start? This is what I decided:

After my amplifier and mixer master are set to "10", I set my gains to about -3db for the most "underpowered" song, I control everything with my lever and it is all good.
 
How about this put in a pink noise CD and set your mixer so the meter is hitting + 6 DB or the first red light over 0DB (or + 1.4) unity gain. the turn on the amp (with the gains at infinity) then slowly turn the gains up until you the clip lights just start to light. This is if these are the only items in the chain, but you have now come close to balancing the system the poor man's way.
 
How about this put in a pink noise CD and set your mixer so the meter is hitting + 6 DB or the first red light over 0DB (or + 1.4) unity gain.

My problem was that a local sound technician for the largest sound company/equipment dealer in town taught me that the gains (the knobs at the top of my GEMINI mixer) should be set as low as possible "for more headroom".

I took your advice and now my PEAVEY system kicks even MORE butt than before.

Thanks again.
 
My problem was that a local sound technician for the largest sound company/equipment dealer in town taught me that the gains (the knobs at the top of my GEMINI mixer) should be set as low as possible "for more headroom".

I took your advice and now my PEAVEY system kicks even MORE butt than before.

Thanks again.

While what your sound guy told you may hold some truth to it, it may also depends on the original signal, for example, gain may differ between microphone signal, turntable signal, tape signal all pretty much analog, which are different that the digital signal from your cd/mp3 media.

You will find that the Bass coming out of the turntable, carries a continuous warm sound, very much different than the stippling sound of a cd.

My Mixers come with a signal display per channel, that is one of my requirements, and I don't let the original signal pass the second yellow bar, under any circumstance, and I know it takes a lot of discipline, but my gain is set to like on 5 out of 10.

Any sound increase I do it out of the master, so I can kick some serious ass. My Amp I hardly ever touch, most of my sound i do with the master or the channel slider, the gain I hardly ever have to mess with.

I do leave PLENTY OF OVER HEAD. This is my own formula:

Mixer Channel: 8
Mixer Master: 1 ~ 8
MIxer Gain: 3 ~ 6
Mixer EQ ch: FLAT -0-
Amp: 4~8

If you look at the picture on my mixer, you will see I was adjusting line one, coming back on the gain, being cued at the time i took the photo, then see channel two, was actually playing, then the master notice was very LOW...

This was ambience music being played... (jazz) as the party had not even started yet, and people were still coming in.




The last time I pushed my master to 10, the cops came. LOL i guess they didn't like my live :sqbiggrin: version of YMCA
 

Attachments

  • i84925719_63726.gif
    i84925719_63726.gif
    220.8 KB · Views: 3
  • DSCN2284.jpg
    DSCN2284.jpg
    107.2 KB · Views: 6
Seriously Horrible Horrible Horrible

I had a nightmare last night. I was the DJ at a wedding, and I had forgotten to do a sound check. And people were there. It was already COCKTAIL HOUR. And I forgot what Mr. Miller taught me.

:sqeek: